Makita DUA300 Betriebsanleitung Seite 16

Attaching the shoulder harness
CAUTION:
When you use the tool in combi-
nation of the backpack-type power supply such
as portable power pack, do not use the shoulder
harness included in the tool package, but use the
hanging band recommended by Makita.
If you put on the shoulder harness included in the
tool package and the shoulder harness of the back-
pack-type power supply at the same time, removing
the tool or backpack-type power supply is difficult in
case of an emergency, and it may cause an accident
or injury. For the recommended hanging band, ask
Makita Authorized Service Centers.
CAUTION:
Always use the shoulder harness
attached to the tool. Before operation, adjust the
shoulder harness according to the user size to
prevent fatigue.
CAUTION:
Before operation, make sure that
the shoulder harness is properly attached to the
hanger on the tool.
CAUTION:
Before operation, make sure that
the buckle of the shoulder harness is fastened
firmly.
CAUTION:
Always use the shoulder harness
dedicated to this tool. Do not use other shoulder
harnesses.
1. Put on the shoulder harness and fasten the buckle.
► Fig.17: 1. Buckle
NOTE: When removing the shoulder harness, unlock
the buckle and remove the shoulder harness.
2.
Adjust the shoulder harness to a comfortable
working position.
► Fig.18
3. Clasp the hook on the shoulder harness to tool's hanger.
► Fig.19: 1. Hook 2. Hanger
The shoulder harness features a means of quick
release. Simply squeeze the sides of the buckle to
release the shoulder harness.
► Fig.20: 1. Buckle
Working with the tool
CAUTION:
Keep all parts of the body away
from the saw chain when the motor is operating.
CAUTION:
Hold the tool firmly with both
hands when the motor is running.
CAUTION:
Do not overreach. Keep proper
footing and balance at all times.
CAUTION:
When cutting through branches,
be careful not to lose your balance due to the
weight of the tool head.
CAUTION:
Always keep escape route in case
a cut branch falls towards the operator.
CAUTION:
Never use the tip of the guide bar
for cutting. Otherwise, dangerous kickback may
occur, and it may result in personal injury.
NOTICE:
Never toss or drop the tool.
NOTICE:
Do not cover the vents of the tool.
NOTICE:
Do not force the tool. Otherwise, it may
damage the tool.
Stand on a stable surface, and hold the tool away from
the branches so that the angle of the tool becomes 60°
or less against the horizontal ground.
► Fig.21: 1. 60° or less
Start the tool, and then press the saw chain onto the branch lightly.
When cutting long branches, in order to control the drop position
of cut branches, divide the branch in sections and cut the branch
from the tip. Pay attention to the falling branches since they may
bounce in the direction of the operator after hitting the ground.
► Fig.22
When cutting thick branches, first make a shallow
undercut and then make the finish cut from the top.
► Fig.23
If you try to cut off thick branches from the bottom, the
branch may close in and pinch the saw chain in the cut.
If you try to cut off thick branches from the top without a
shallow undercut, the branch may splinter.
► Fig.24
Carrying tool
Before carrying the tool, always remove the battery car-
tridges from the tool, and then attach the guide bar cover.
Also cover the battery cartridge with the battery cover.
► Fig.25: 1. Guide bar cover 2. Battery cover
Using the tool with battery adapter
Optional accessory
Use the hanging band when you use the tool with battery adapter.
Attaching the hanging band
1. Attach the hooks of the hanging band to the rings of the
shoulder harness or waist belt as shown in the figure. Select the
type of band and the connecting method appropriate for your usage.
► Fig.26: 1. Ring 2. Hook
► Fig.27: 1. Ring 2. Hook
2. Attach the hook to the tool.
► Fig.28: 1. Hook
Detaching the tool
When setting down the tool, unlock the buckle on the hanging
band with one hand while holding the tool with the other hand.
► Fig.29: 1. Buckle
NOTE: The buckle is not equipped depending on the
type of band.
If you need to release the tool quickly, follow the steps below.
1. Push the levers on the buckle of the waist belt to
unlock the buckle.
► Fig.30: 1. Buckle 2. Lever
2. Take off the shoulder harness to release the tool
and the unit.
► Fig.31: 1. Shoulder harness
16 ENGLISH