Brief Instructions - VOLTCRAFT DSO-3074 Kurzanleitung

Brief instructions

„DSO-3074" USB oscilloscope
„DSO-3104" USB oscilloscope
„DSO-3204" USB oscilloscope
Item no. 1490904
Item no. 1490960
Item no. 1490962
Intended use
The oscilloscope unit is intended for use in combination with a Windows
two USB 2.0 interfaces as a fully digital storage oscilloscope (short DSO) for the visualisation of
electrical quantities and signals. There are four independent input channels available for mea-
surement. The probes are connected to the DSO via BNC connectors. Operation and display
is performed using the enclosed measurement program. It is equivalent to a real oscilloscope
operating interface.
The bandwidth and the sampling rate depend on the type, as follows:
DSO-3074 USB DC - 70 MHz at 1 GS/s
DSO-3104 USB DC - 100 MHz at 1 GS/s
DSO-3204 USB DC - 200 MHz at 1 GS/s
The maximum input values, 35 V/DC or 35 V/AC, indicated on the device may never be ex-
ceeded.
Any use other than that described above could lead to damage to this product and involves the
risk of short circuits, fire, electric shock, etc.
No part of the product may be modified or rebuilt, and the housing must not be opened.
Measurements are not permitted in damp rooms or outdoors, nor under adverse environmental
conditions.
Adverse environmental conditions are:
- Wet conditions or high air humidity,
- Dust and flammable gases, vapours or solvents,
- Thunderstorms or similar conditions such as strong electrostatic fields, etc.
This quick guide explains the safety measures that should be taken to make working with the
device as safe as possible. The individual device functions are explained in more detail in the
help menu of the Windows program or in the APP.
Always observe the safety instructions of these operating instructions or the help menu.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• USB oscilloscope
• USB cable
• Software and operating instructions on CD
• Brief instructions
Up-to-date operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code. Follow the instructions on the websit
Safety instructions
Please read through the quick guide carefully before using the device. It
contains important information on its correct operation.
The warranty will be void in the event of damage caused by failure to observe
these safety instructions! We do not assume any liability for any resulting
damage!
We shall not accept liability for damage to property or personal injury caused
by incorrect handling or non-compliance with the safety instructions! In such
cases, the warranty will be null and void.
• The unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons. Do not disassemble the product.
• The product is not a toy. Therefore, be especially careful when children are around.
based computer with
®
• First, connect the measurement cable to the oscilloscope; then connect the probe
to the signal measuring circuit to be tested. After finishing the measurements,
disconnect the measurement leads from the circuit first and then disconnect the
cable from the oscilloscope.
• Take particular care when dealing with voltages exceeding 30 V/AC or 30 V/DC!
Even at these voltages, there is a danger of fatal electric shock if you touch electric
conductors.
• Do not use the device in rooms or under unfavourable ambient conditions in which
there are or could be combustible gases, vapours or dust.
• Do not use in the immediate vicinity of:
- strong magnetic or electromagnetic fields
- transmitting aerials or HF generators
These can distort the measurement.
• Use only measurement lines and accessories for the measurement that match the
specifications of the oscilloscope.
• If a safe operation can no longer be assumed, the device must be put out of ope-
ration and secured against unintended operation. Safe operation can no longer
be assumed if:
- the product shows visible damage,
- does not function any longer and
- the unit was stored under unfavourable conditions for a long period of time or
- it has been subjected to considerable stress in transit.
• Never switch the device on immediately after having taken it from a cold to a warm
environment. The condensation that forms might destroy your device. Allow the
device to reach room temperature before switching it on.
• Do not disassemble the product! There is risk of a life-threatening electric shock!
• Do not carelessly leave the packaging material lying around, since it could be-
come a dangerous plaything for children.
• The device is intended only for dry interior rooms (not bathrooms or similar damp
rooms). The device must not get wet or damp. There is risk of a life-threatening
electric shock!
• On industrial sites, the accident prevention regulations of the association of the
industrial workers' society for electrical equipment and utilities must be followed.
• Measurement instruments used at schools, training facilities, do-it-yourself and
hobby workshops should not be handled unless supervised by trained, respon-
sible personnel.
• If you have doubts about how the device should be operated or how to connect it
safely, consult a trained technician.
• Please handle the product carefully. The product can be damaged if crushed,
struck or dropped, even from a low height.
• Regularly check the technical safety of the device and the measuring cables,
e.g., for damage to the casing or pinching of the cables etc. The device may
in no case be opened or used, if the covers have been removed.
!RISK OF FATAL INJURY!
Never exceed the maximum admissible input values. Never touch circuits or
parts of circuits when they may contain voltages greater than 30 V/AC rms
or 30 V/DC! Danger to life!
• If in doubt about how to connect the device correctly, or should any questions arise
that are not answered in these operating instructions, please contact our technical
service or another specialist.