AEG BUS18BL Originalbetriebsanleitung Seite 18

Technical Data
Reciprocating Saw
Production code
Battery voltage
Stroke rate under no-load
Lengths of stroke
Cutting depth max. in:
Wood
Steel
PVC Pipes / Sections
Weight according EPTA-Procedure 01/2014
(Li-Ion 2,0 Ah...9,0Ah)
Recommended Ambient Operating
Temperature
Recommended battery types
Recommended charger
Noise information
Measured values determined according to EN 62841. Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty
K=5dB(A))
Sound power level (Uncertainty K=5dB(A))
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according
to EN 62841
Cutting boards *1:
Cutting wooden beams *2:
Vibration emission value a
h, B
Uncertainty K=
Cutting wooden beams
Vibration emission value a
h, WB
Uncertainty K=
*1 with sawblade dimension 152,5 x 1,3/1,65 mm and tooth pitch 4,2 mm, 6 Tpi
*2 with sawblade dimension 152,5 x 1,3/1,65 mm and tooth pitch 4,2 mm, 6 Tpi
WARNING
The vibration and noise emission level given in this information
sheet has been measured in accordance with a standardized test
given in EN 62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the
main applications of the tool. However if the tool is used for di e-
rent applications, with di erent accessories or poorly maintained,
the vibration and noise emission may di er. This may signi cantly
increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should
also take into account the times when the tool is switched o or
when it is running but not actually doing the job. This may signi -
cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from
the e ects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work
BUS18BL
patterns.
4745 27 02... Wear ear protectors. Exposure to noise can cause hearing loss.
... 000001-999999
18 V
WARNING! Read all safety warnings, instructions, illustrations
0 - 3200 min
-1
and speci cations provided with this power tool. Failure to follow
28,5 mm
all instructions listed below may result in electric shock, re and/or
serious injury.
255 mm
Save all warnings and instructions for future reference.
20 mm
130 mm
SABRE SAW SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when
3,6 kg..., 4,3 kg
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a "live"
-18°C ... +50°C
wire may make exposed metal parts of the power tool "live" and
L1820R...,L1890RHD
could give the operator an electric shock.
BLK1218, BL1418,
Use clamps or another practical way to secure and support
BL1218, AL1218G,
the workpiece to a stable platform. Holding the workpiece by
AL18G
hand or against your body leaves it unstable and may lead to loss
of control.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
87 dB (A)
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is recom-
98 dB (A)
mended, such as dust mask, protective gloves, sturdy non-slip
footwear, helmet and ear defenders.
Chips and splinters must not be removed while the machine is
running.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Do not use cracked or distorted saw blades.
Plunge cuts without pre-drilling a hole are possible with soft mate-
rials (wood, light building materials for walls). Harder materials
15,2 m/s
2
(metals) must rst be drilled with a hole corresponding to the size
1,5 m/s
2
of the saw blade.
Always place the guide shoe on the workpiece when sawing.
15,2 m/s
2
1,5 m/s When working in walls ceiling, or oor, take care to avoid electric
2
cables and gas or waterpipes.
To avoid unintended start of the product, place down tool only on
even surfaces.
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device o immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
Possible causes can be:
• it is tilted in the workpiece to be machined
• breakage of the material to be used
• the power tool is overloaded
WARNING! Danger of burns
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
Do not let any metal parts enter the airing slots - danger of short
circuit!
GB
English
15