Makita DHS710 Bedienungsanleitung Seite 9

Overheat protection for tool
When the
automatically and the overheat indicator lights up about
60 seconds. In this situation, let the tool cool before
turning the tool on again.
Overheat protection for battery
When the battery is overheated, the tool stops
automatically without any indications. The tool does not
start even if pulling the switch trigger. In this situation,
let the battery cool before turning the tool on again.
NOTE:
The battery overheat protection works only with a
battery cartridge with a star marking.
Fig.3
Overdischarge protection
When the remaining battery capacity gets low, the
battery indicator blinks on the applicable battery side.
By further use, the tool stops and the battery indicator
lights up about 10 seconds. In this situation, charge the
battery cartridge.
Adjusting depth of cut
Fig.4
CAUTION:
After adjusting the depth of cut, always tighten the
•
lever securely.
Loosen the lever on the depth guide and move the base
up or down. At the desired depth of cut, secure the base
by tightening the lever.
For cleaner, safer cuts, set cut depth so that no more
than one blade tooth projects below workpiece. Using
proper cut depth helps to reduce potential for dangerous
KICKBACKS which can cause personal injury.
Bevel cutting
Fig.5
Fig.6
Loosen the front lever and rear wing nut. Set for the
desired angle (0° - 50°) by tilting accordingly, then
tighten the lever and wing nut securely.
Fig.7
Use the 45° stopper when you do precise 45° angle
cutting. Turn the stopper clockwise fully for bevel cut (0°
- 45°) and turn it counterclockwise for 0° - 50° bevel
cuts.
Sighting
Fig.8
For straight cuts, align the 0° position on the front of the
base with your cutting line. For 45° bevel cuts, align the
45° position with it. The position of the top guide is
adjustable.
Downloaded from www.Manualslib.com
tool is overheated, the
manuals search engine
Switch action
tool stops
Fig.9
CAUTION:
Before installing the battery cartridge into the tool,
•
always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released.
Do not pull the switch trigger hard without pressing
•
the lock-off lever. This can cause switch breakage.
To prevent the switch trigger from being accidentally
pulled, a lock-off lever is provided. To start the tool,
press the lock-off lever and pull the switch trigger.
Release the switch trigger to stop.
WARNING:
For your safety, this tool is equipped with lock-off
•
lever which prevents the tool from unintended
starting. NEVER use the tool if it runs when you
simply pull the switch trigger without pressing the
lock-off lever. Return tool to a MAKITA service
center for proper repairs BEFORE further usage.
NEVER tape down or defeat purpose and function
•
of lock-off lever.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Removing or installing saw blade
CAUTION:
Be sure the blade is installed with teeth pointing
•
up at the front of the tool.
Use only the Makita wrench to install or remove
•
the blade.
Fig.10
To remove the blade, press the shaft lock so that the
blade cannot revolve and use the wrench to loosen the
hex bolt counterclockwise. Then remove the hex bolt,
outer flange and blade.
For tool with the inner flange for other than
15.88 mm hole-diameter saw blade
Fig.11
The inner flange has a certain diameter protrusion on
one side of it and a different diameter protrusion on the
other side. Choose a correct side on which protrusion
fits into the saw blade hole perfectly.
Next, mount the inner flange onto the mounting shaft so
that the correct side of protrusion on the inner flange
faces outward and then place saw blade and outer
flange.
BE SURE TO TIGHTEN THE HEX BOLT CLOCKWISE
SECURELY.
9