Warranty And Liability; Declaration Of Conformity; Environmental Protection, Disposal - Fein GSZ4-280EL Bedienungsanleitung

en
24
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a stand-
ardised test given in EN 60745 and may be used to
compare one tool with another. It may be used for a
preliminary assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is
used for different applications, with different accesso-
ries or poorly maintained, the vibration emission may
differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool
is switched off or when it is running but not actually
doing the job. This may significantly reduce the expo-
sure level over the total working period.
Identify additional safety measures to protect the oper-
ator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organi-
sation of work patterns.
The vibrational emission values are given for dry grind-
ing of metal with grinding points. Other applications,
such as shaping with hard metal cutters, can lead to
other vibrational emission values.
Handling hazardous dusts
For work procedures with this power tool where
material is removed, dusts develop that can be hazard-
ous to one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate parti-
cles from materials containing stone, paint solvents,
wood preservatives, antifouling paints for vessels, can
trigger allergic reactions to the operator or bystanders
and/or lead to respiratory infections, cancer, birth
defects or other reproductive harm. The risk from
inhaling dusts depends on the exposition. Use dust
extraction matched appropriately for the developing
dust, as well as personal protective equipment and pro-
vide for good ventilation of the workplace. Leave the
processing of asbestos-containing materials to special-
ists.
Wood and light-metal dust, hot mixtures of grinding
dust and chemical materials can self-ignite under unfa-
vourable conditions or cause an explosion. Avoid
sparking in the direction of the dust collector as well as
overheating of the power tool and the materials being
sanded, empty the dust collector/container in time,
observe the material manufacturer's working instruc-
tions, as well as the relevant regulations in your country
for the materials being worked.
Operating Instructions.
The self-start lock (for GSZ8..., GSZ11...) prevents the
straight grinder from automatically restarting again,
even after a brief interruption of the power supply dur-
ing operation, e. g., from a pulled mains plug.
The straight grinder is fitted with overload and blocking
protection (for models GSZ8..., GSZ11...). In case of
overload or blocking of the application tool, the power
supply is interrupted. In this case, switch the power tool
off, remove it from the workpiece and check the appli-
cation tool. Afterwards, switch the power tool on again.
Use a collet that fits the grinding accessory.
Insert the clamping shaft of the grinding accessory to
the stop into the collet chuck.
Observe the maximum permitted projecting shaft
length (a) of the grinding accessory according to the
manufacturer's instructions (see page 13).
Move the power tool back and forth applying uniform
pressure, so that the workpiece surface does not
become too hot.
Repair and customer service.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via
the ventilation slots frequently with dry and oil-free
compressed air, and connect a residual current device
(RCD) on the line side.
If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared cord available
through the FEIN customer service centre.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
If required, you can change the following parts your-
self:
Application tools, collet

Warranty and liability.

The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the
last page of this Instruction Manual.
Technical documents at: C. & E. Fein GmbH,
D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out power tools and accessories
should be sorted for environmental-friendly recycling.
Selection of accessories (see page 13).
Use only original FEIN accessories. The accessories
must be intended for the power tool type.
A Collet