RadioLink AT9S Bedienungsanleitung Seite 5

3.3.13 THR-DELAY (ACRO) ............................................ .................................................. ....... 53
THR CURVE (ACRO) ............................................. .................................................. .... 54
3.3.14
THROTTLE-NEEDLE-Mischen (ACRO / HELI) ......................................... ................... 55
3.3.15
4 TEIL 4 FUNKTIONEN DES GLIDERMODELLS ............................................. ..................................... 57
SET BASIC MENU OF GLID ............................................. .................................................. 57
4.1
SET GLID TYPE ............................................... .................................................. ................... 58
4.2
GLID ADVANCE MENU ............................................... .................................................. ..... 59
4.3
4.3.1 AILE DIFF (FINDEN IM ACRO-FUNKTIONSMENÜ 3.3.5) ...................................... .......... 59
4.3.2 FLAPERON (GLID 1A + 1F, FINDEN IM ACRO-FUNKTIONSMENÜ 3.3.3) ....................... 59
4.3.3 V-TAIL (FINDEN IM ACRO-FUNKTIONSMENÜ 3.3.10) ..................................... ............... 59
4.3.4 OFFSET (GLID 2A + 2F): .......................................... .................................................. ....... 59
4.3.5 STARTVERZÖGERUNG (nur GLID 1A + 1F) ......................................... ....................................... 60
4.3.6 CHAMBER-FLP ............................................... .................................................. ............... 61
4.3.7 Sturzmischung ................................................ .................................................. ................. 62
4.3.8 SCHMETTERLING (Krähe) mischen ............................................. ................................................ 62
4.3.9 AILE / RUDD MIX .............................................. .................................................. ............. 64
ELEV-FLAP-Mischen (siehe GLID-Menü 3.3.7) ...................................... .......................... 64
4.3.10
AILE-FLAP (nur GLID 2A + 2F) ........................................ ........................................... 64
4.3.11
SPOILER MIX (GLID) ............................................. .................................................. ... 65
4.3.12
FLAP-TRIM (siehe GLID 3.3.4) ........................................ ............................................... 66
4.3.13
BEDINGUNG................................................. .................................................. ............... 66
4.3.14
5 Teil. 5 HUBSCHRAUBERMODELLFUNKTIONEN ............................................... ........................... 67
5.1
GRUNDLEGENDE EINSTELLUNG MIT HUBSCHRAUBER .............................................. ................................ 67
5.2 HELI-SPEZIFISCHE GRUNDMENÜFUNKTIONEN ............................................ ........................ 68
5.2.1 Taumelscheibentypen ............................................... .................................................. ............. 69
5.2.2 SWASH AFR (nicht in SWH1) ........................................... .................................................. 70
5.3
HELI-SPEZIFISCHE FUNKTIONEN DES ADVANCE-MENÜS ............................................ ................ 71
5.3.1 THR-CURVE und PIT-CURVE ........................................... .............................................. 71
5.3.2 REVO MIX: ............................................... .................................................. ....................... 72
5.3.3 GYRO SENSE ................................................ .................................................. .................. 74
5.3.4 THROTTLE HOLD ................................................ .................................................. .......... 75
5.3.5 HOVERING-EINSTELLUNGEN (HOV-THR und HOV-PIT) ....................................... ...... 75
5.3.6 HIGH / LOW PITCH (HI / LO-PIT) ....................................... ............................................... 76
5.3.7 OFFSET ................................................. .................................................. ........................... 77
5.3.8 VERZÖGERN................................................. .................................................. ............................ 78
5.3.9 GOVERNORS ................................................. .................................................. ................. 78
Gasmischung (THROTTLE MIX) ............................................ .................................. 80
5.3.10
SWASH-RING ............................................... .................................................. .............. 80
5.3.11
DROSSELNADEL (siehe ACRO-MENÜ 3.3.15) ........................................ .............. 81
5.3.12
PROG MIX (siehe ACRO MENU 3.3.1) ........................................ .................................. 81
5.3.13
BEDINGUNG................................................. .................................................. ............... 81
5.3.14
6 Teil 6. MULTIROTOR-FUNKTIONEN ............................................. ........................................... 83
6.1 MULTIROTOR BASIC MENU ............................................... .............................................. 84
6.1.1 MODELLTYP................................................ .................................................. ................. 84
6.1.2 AUX-Kanaleinstellung ............................................... .................................................. ......... 85
6.2 ADVANCEMENU FÜR MULTIROTOR ............................................... .............................. 85
6.2.1 EINSTELLUNG................................................. .................................................. ...................... 85
6.2.2 DROSSELKURVE (siehe ACRO 3.3.14) ......................................... ................................ 86
6.2.3 PROG. MIX (siehe ACRO 3.3.1) .......................................... ................................................ 86
4