Troubleshooting - Kobra HYBRID Betriebsanleitung

IMPORTANT WARNINGS
BEFORE TURNING ON THE MACHINE CAREFULLY READ
THE INSTRUCTIONS FOR USE AND THE FOLLOWING
WARNINGS.
Before plugging in the appliance make sure that the voltage
and mains frequency match to those on the plate on the
front of the machine.
UNPLUG THE POWER CABLE FROM THE MAINS IN THE
FOLLOWING CASES:
- BEFORE LIFTING THE MACHINE FROM ITS BIN AND
BEFORE EMPTYING THE BIN
- BEFORE CARRYING OUT ANY MAINTENANCE OR
REPAIRS OR WORKING ON THE INNER PARTS OF
THE MACHINE.
- UNPLUG THIS EQUIPMENT WHEN NOT IN USE FOR
AN EXTENDED PERIOD OF TIME.
The machine shreds continuously at nominal voltage,
intermittent operation at nominal voltage +10%.
Congratulations on the purchase of your KOBRA HYBRID
shredder, one of the latest generation of KOBRA products.
KOBRA HYBRID comes with a special innovative energy
management system storing energy during normal
document shredding and then releasing it (when LEDs
are off) so that some documents can be shredded
disconnecting the machine from the mains for maximum
energy savings and zero consumption in stand-by.
INSTALLATION
For appliances provided with mains plug use a socket outlet
which is easily accessible near the machine and provided
with a protective earthing connection.
Remove the machine from its packaging and place the
shredding unit on the bin as indicated in figure 1.
There is a transparent window on the front which allows you
to check the level of shredded paper inside so the operator
can empty the bin when it is full.
USING THE APPLIANCE
After plugging in the machine turn the switch "A" to the
position "FWD". The machine is ready to shred paper.
- Automatic START / STOP
Insert the paper to be shredded in the throat "C", the LED "D"
come on and the machine automatically starts shredding.
Centre credit cards to be shredded when you insert them
in order to activate button "B". The LED indicators switch off
automatically when the stored energy has been used and
the machine stops automatically.
- CENTRE BUTTON "B"
The centre button "B" allows you to turn the machine on
manually in case of light and fine paper which may fail to
activate the machine.
- PAPER JAMS.
The machine will jam if a quantity of paper in excess of the
cutting capacity is inserted.
4
CAUTION
PAY CAREFUL ATTENTION TO THE FOLLOWING
WARNINGS PRINTED ON THE TOP OF THE MACHINE:
REFER TO THE OPERATING INSTRUCTIONS
CAUTION, MOVING PARTS
WARNING!
SAFETY PRECAUTIONS
KEEP NECK TIES OR OTHER DANGLING OBJECTS
AWAY FROM THE THROAT
DO NOT PUT YOUR HANDS IN THE THROAT
AND THE CUTTING KNIVES
DO NOT ALLOW CHILDREN
TO OPERATE THE DEVICE
KEEP LONG HAIR AWAY
FROM THE THROAT
DO NOT USE AEROSOL PRODUCTS OR
LUBRICANTS
To clear the machine from a paper jam proceed as follows:
Turn switch "A" to the " REV " position and hold it down until
the paper is all out of the throat "C".
Turn switch "A" back to the " FWD " position and insert a
smaller amount of paper to be shredded.
IMPORTANT!
If you turn the switch "A" to the position "0" all functions are
switched off and the machine stops immediately.
To reset the automatic functions, turn switch "A" to the
"FWD" position.
You are advised to limit jams caused by inserting too
much paper and to operate the machine below maximum
capacity in order to prolong the life of the mechanical parts
and the life of the machine itself.
Continuous jams may cause breakage of the transmission
mechanisms and void the warranty.
Inserting foreign bodies or material may damage the
cutting knives and void the warranty.
CARE AND MAINTENANCE
KOBRA HYBRID shredders have no need for any specific
care or maintenance.
In any case, when you notice a considerable reduction in
cutting capacity, lubricate the cutting knives by shredding
a sheet of paper sprinkled with some drops of oil that
comes with the machine.
NEVER use synthetic oil, benzene based products or aerosol
lubricants of any kind inside the appliance or in its vicinity.
Fire hazard
KOBRA Hybrid

TROUBLESHOOTING

If you are having problems with your shredder, check the symptoms and remedies described below.
If this fails to solve the problem, contact your nearest Kobra dealer.
Never open the shredding unit or to try to repair it. You run the risk of serious electric shock and void your warranty.
PROBLEM WHAT HAPPENS
The shredder does not Paper is inserted
start into the throat of the
machine and it does
not start
Considerable reduction Capacity is reduced
of shredding capacity compared with capacity
seen when cutting kni-
ves are oiled
FIGURE 1
CAUSE ACTION
• Position of switch "A" • Turn the switch to " FWD"
• Motor in heat protection • Wait about 15 minutes
mode for the engine to cool
down
• Power cord not
plugged in propery • Check that the plug is
inserted into the power
• No electrical power socket properly
supply
• Check that there is power
to the socket
Cutting knives not oiled Lubricate cutting knives
DECLARATION OF COMPLIANCE
Compliant with - directive LVD 2014/35/UE
- directive 2011/65/EU RoHS
- directive EMC 2014/30/UE
The manufacturer ELCOMAN SRL
VIA GORIZIA,9 20813 BOVISIO MASCIAGO (MI) – ITALY
Hereby declares that the KOBRA shredders described
below are in compliance with the standards set down in the
directive LVD 2014/35/UE
- KOBRA series: Kobra HYBRID
The standards applied are:
EN 62368-1:2014+A11:2017
EN 55014-1:2017
EN 55014-2 :2015
EN 61000-3-2 :2019
EN 61000-3-3 :2013
Bovisio Masciago, 31.05.2019
Technical Office
KOBRA Hybrid
A. DE ROSA
5