Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
14 | English
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Speed preselection thumbwheel
a)
(2) Battery
a)
(3) Battery release button
(4) Sanding disc
(5) Battery charge indicator
(6) On/off switch
(7) Handle (insulated gripping surface)
a)
(8) Sanding net
(9) Sanding disc holder
(10) Dust extraction adapter
a)
(11) Vacuum hose
(12) Rubber band
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Cordless Disc Sander
Article number
Rated voltage
Speed preselection
A)
Idle speed n
min
0
Sanding pad diameter
Weight according to EPTA-
A)
Procedure 01:2014
Recommended ambient
temperature during char-
ging
Permitted ambient temper-
B)
ature during operation
and
during storage
Recommended re-
chargeable batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according
to EN 62841-2-4.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). The noise level when working can
exceed the volume stated. Wear hearing protection!
Total vibration values a
(triax vector sum) and uncertainty K
h
determined according to EN 62841-2-4:
2
2
a
= 2.5 m/s
, K = 1.5 m/s
.
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
1 609 92A 66A | (26.01.2021)
EasyCurvSander 12
3 603 JC9 0..
V
12
●
-1
800–1800
mm
38
kg
0.5
°C
0 to +35
°C
–20 to +50
PBA 12V...
GAL 12...
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery (see figure A)
To remove the battery (2), press the release buttons (3) and
pull the battery out of the power tool. Do not use force to
do this.
Battery charge indicator
The battery charge indicator (5) on the power tool consists
of three green LEDs. It indicates the battery's state of charge
for a few seconds after the power tool is switched on and off.
LED
Continuous lighting 3 x green
Capacity
60–100%
Bosch Power Tools
Werbung
Inhaltsverzeichnis
