Philips SENSOTOUCH 3D RQ1290 Bedienungsanleitung Seite 8

English
8
Note: When you place the shaver in the plugged-in charger or Jet Clean System, the travel lock is automatically deactivated.
power-saving mode (RQ1290 only)
The appliance is equipped with an automatic power-saving mode. When the shaver enters the power-saving mode, the light in the on/off button
goes out to save energy.
- If you move the appliance for 5 minutes without switching it on, it automatically goes into power-saving mode.
The lock symbol flashes on the display to indicate that the appliance is in power-saving mode. (Fig. 16)
,
- To deactivate the power-saving mode, simply press the on/off button.
Blocked shaving heads
- If the shaving heads are blocked, the shaving unit symbol, the tap symbol and the exclamation mark flash. In this case, the motor cannot run
because the shaving heads are soiled or damaged. (Fig. 17)
Note: The displays of types RQ1290, RQ1280, RQ1260 and RQ1250 look different, but show the same symbols.
- When this happens, you have to clean the shaving unit or replace it.
- The shaving unit symbol, the tap symbol and the exclamation mark continue to flash until you unblock the shaving heads.
charging
Charging takes approx. 1 hour.
RQ1290/RQ1280/RQ1260: A fully charged shaver has a shaving time of up to 60 minutes/20 days.
RQ1250: A fully charged shaver has a shaving time of up to 50 minutes/16 days.
The actual shaving time is calculated by the shaver. If you have a heavy beard, the shaving time may be less than expected. The shaving time may
also vary over time, depending on your shaving behaviour and beard type.
Charge the shaver before you use it for the first time and when the display indicates that the battery is almost empty (see section 'Battery low'
in chapter 'The display').
Quick charge
After the shaver has charged for 5 minutes, it contains enough energy for one shave.
charging in the charger
1 Put the small plug in the charger (Fig. 18).
2 Put the adapter in the wall socket.
3 Put the shaver in the charger and push it backwards ('click'). (Fig. 19)
The display shows that the shaver is charging (see chapter 'The display').
,
charging in the Jet clean system (specific types only)
1 Put the small plug in the Jet Clean System.
2 Put the adapter in the wall socket.
3 Place the shaver upside down in the holder with the display pointing towards the front of the Jet Clean System (Fig. 20).
Note: The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit.
Note: RQ1290 only: when you turn the shaver upside down, the minutes indication on the display is also turned upside down so you can still see to
what level the battery is charged.
4 Press the shaver tightly into the holder to lock it into place (Fig. 21).
The display shows that the shaver is charging (see section 'Charging' in chapter 'The display').
,
using the shaver
shaving
1 Press the on/off button once to switch on the shaver.
The display lights up for a few seconds.
,
2 Move the shaving heads over your skin. Make circular movements (Fig. 22).
- Do not make straight movements.
- Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system.
3 Press the on/off button once to switch off the shaver.
The display lights up for a few seconds and then shows the remaining battery capacity.
,
Wet shaving
You can also use this shaver on a wet face with shaving foam or shaving gel.
To shave with shaving foam or shaving gel, follow the steps below:
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure that the shaving unit glides smoothly over your skin.
4 Press the on/off button once to switch on the shaver.
5 Move the shaving heads in circular movements over your skin.
Note: Rinse the shaver under the tap regularly to ensure that it continues to glide smoothly over your skin.
6 Dry your face and thoroughly clean the shaver after use (see chapter 'Cleaning and maintenance').
Note: Make sure you rinse all foam or shaving gel off the shaver.