Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1. Make sure the switch (2) is at the "0" position and the appli-
ance disconnected from the mains.
2. Push the ends of the dough hooks or beaters into the
respective fittings until they lock into place. Slightly turning
the accessories might help facilitate the process of attach-
ing.
Disassembly of dough hooks / beaters
Press the release button (1) to release the accessories. This is
only possible, when the switch is set to the "0" position or the
blender stick symbol.
Assembly of the blender stick
NOTE:
•
For safety reasons, the blender stick cannot be used
once the dough hooks or beaters are attached.
•
The fixture for attaching the blender stick (6) is located on
the bottom of the appliance.
1. Make sure that the switch is set to the "0" position and that
the appliance disconnected from the mains.
2. Slide the protective cover open in order to expose the
fixture.
3. Push the blender stick (4) into the fixture until it rests
completely. Lock the blender stick by turning it counter-
clockwise as far as it will go.
Disassembly of the blender stick
In order to release the blender stick from the housing, turn it
clockwise and pull it off.
Instructions for use
•
For best results, use high-quality containers that are not too
big.
•
In order to avoid splashing, submerge the dough hooks or
beaters into the food to be mixed before switching on the
appliance.
•
Start with a low speed setting (1 – 2) and then select a
higher setting if necessary.
•
After switching off the appliance, wait until the motor comes
to a complete stop before removing the dough hooks or
beaters from the food.
•
The appliance is suitable for small quantities only! Fill
containers with the maximum quantities only as indicated in
the table!
Blender stick
CAUTION:
Do not use the blender stick for cutting hard foodstuff such as
coffee beans, nutmeg or ice cubes. This could damage the
product.
•
Cut larger size ingredients into smaller pieces (max.
Ø 1.5 cm) and add some liquid before pureeing.
32
•
Do not exceed the MAX marking when submerging the
blender stick into the bowl with ingredients.
Electric operation
1. Make sure the switch is at the "0" position.
2. Before you plug the mains plug into the outlet, check
whether the system voltage that you want to use, matches
the one of the appliance. You will find information about it
on the type plate.
3. Connect the appliance to a correctly installed grounded
outlet.
Switch (2)
Speed settings for dough hooks or beaters
Appliance off
Switch position for ejecting the
dough hooks or beaters
Blender stick mode
Turning on/off
Using the dough hooks and beaters
•
In order to switch on the appliance, set the switch to one of
the positions from "1" to "5".
•
When at the "0" position, the appliance is switched off.
Using the blender stick
1. Set the switch to the blender stick symbol.
2. Press the TURBO button (3).
3. When releasing the button, the appliance will stop.
4. Set the switch to the "0" position.
NOTE:
When assembling the blender stick, a safety switch will
deactivate the speed settings.
Turbo operating mode
All speed settings allow you to temporarily switch to the highest
speed setting. In order to do so, press the TURBO button dur-
ing operation. When activating the button in short intervals, you
will achieve a pulse operation.
CAUTION: Short-term operation
•
In speed setting modes 1 to 5, the maximum operat-
ing time of 5 minutes per operating cycle must not be
exceeded.
•
When using the blender stick, the operating time per
operating cycle is only 1 minute.
•
Wait at least 10 minutes between two operating cycles.
Werbung
Inhaltsverzeichnis
