VOLTCRAFT CPAS-4800/4 Bedienungsanleitung Seite 2

OPERATING INSTRUCTIONS
CPAS-4800/4 USB CAR CHARGER
ITEM NO.: 1362461
INTENDED USE
The product is designed to charge and operate up to four USB devices in a vehicle. Power
is supplied via an on-board voltage socket. The product features overload and short circuit
protection mechanisms. Use the product in dry indoor areas only.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
DELIVERY CONTENT
• USB car charger
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in theses operating instructions, we assume no liability
for any resulting personal injury or damage to property. Such cases will
invalidate the warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
• is visibly damaged,
• is no longer working properly,
• has been stored for extended periods in poor ambient conditions or
• has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Always turn off the connected device before connecting/disconnecting it.
• Unplug the product while it is not in use.
• The product gets hot during use. Ensure sufficient ventilation and never cover the
product during use.
• Do not short-circuit the USB outputs.
• Never use the product immediately after it has been brought from a cold room into
a warm one. The condensation generated could destroy the product. Allow the
device to reach room temperature before connecting and using it. This may take
several hours.
• Never leave the product and the connected device unattended during use.
b) Miscellaneous
• Consult a professional if you require assistance with product operation, safety or
connection.
• Maintenance work, adjustments and repairs may be carried out only by a
professional or at a specialist workshop.
Should you have questions concerning correct product connection or operation, or should
other questions arise that this user manual does not address, please do not hesitate to
contact our technical support or a third-party professional.
PAIRS OF USB PORTS
OPERATION
VERSION 08/15
Always turn off the desired device before connecting it to the USB port.
Make sure the connection is correct. If the product is not connected properly,
it could overheat or cause an electric shock or fire.
Make sure that the device meets the product's power requirements (see
technical data).
You can charge or operate multiple USB devices simultaneously using the product. How
to connect a single USB device is described below.
The total current output of a pair of USB ports must not exceed 2400 mA. If, for
example, one of the USB ports of a pair of USB ports is connected to a USB device
with a current consumption of 2000 mA, the other USB port may only be connected to a
USB device with a current consumption of max. 400 mA.
1. Connect the switched-off USB device to the product.
2. Plug the product into your vehicle's on-board voltage socket. The power indicator on the
product lights up to indicate the product is operational.
3. Your USB device is now charging. Should you wish to operate the USB device, you may
turn it on now.
4. Turn off the USB device before you disconnect the product from your vehicle's on-board
voltage socket.
5. Unplug the product from your vehicle's on-board voltage socket after use.
You can operate the product while the engine is both on or off. However, avoid starting
the engine while the product is connected as this cuts power to the voltage socket
briefly (this may not apply to all vehicle models). If the engine is switched off, drawing
current over a longer period of time will discharge the vehicle battery.
CLEANING
Disconnect the product from the on-board voltage socket before cleaning. Clean the product
with a dry, fiber-free cloth.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
TECHNICAL DATA
Input voltage ................................................ 12 - 24 V/DC
Output voltage / current ............................... 5 V/DC, 2 x 2400 mA per pair of USB ports
Operating conditions .................................... 0 to +35 ºC, 20 – 90 % RH (non-condensing)
Storage conditions ....................................... -20 to +60 ºC, 10 – 90 % RH (non-condensing)
Dimensions (W x H x D) .............................. 48 x 29 x 71 mm
Weight .................................................. ........43 g
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the technical status at the
time of printing.
© Copyright 2015 by Conrad Electronic SE
Pair of USB ports A
Pair of USB ports B
V1_0815_02-ETS-Mkde