Conrad Analog Retro Bedienungsanleitung Seite 2

O P E R A T I N G I N S T R U C T I O N S
Wristwatch Analogue Retro
Item-No. 67 20 66
Intended Use
The wristwatch is intended for displaying the time and date.
The watch may only be powered by a battery (for the type, refer to „Technical data").
Any other use than the one described above may lead to damage to the product and involves other risks, such
as shorts, fire, etc.
No part of the product must be modified or rebuilt.
This product complies with all current National and European requirements.
The safety instructions should be observed without fail.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these safety
instructions. We do not assume liability for any resulting damage.
We shall not accept liability for damage to property or personal injury caused by incor-
rect handling or non-compliance with the safety instructions. The warranty will be null
and void in such cases.
An exclamation mark inside a triangle indicates important instructions in the operating
manual.
The „Hand" symbol indicates special tips and operating information.
• For safety and approval (CE) reasons, unauthorised conversion and/or modifications to the product are not
permitted.
• Keep the product out of the reach of children. It is not a toy.
• Do not expose the product to high temperatures, strong vibrations or heavy mechanical loads.
• If the strap becomes damp or wet, let it dry thoroughly. If the watch is worn for a long period of time, this can
lead to discoloration of the strap and possibly irritation of the skin. Furthermore, this might reduce the life-
time of the watchstrap.
• Do not leave packaging material lying around carelessly. It may become a dangerous plaything for children.
• Please observe the additional safety instructions in the individual chapters of this manual.
• If you have any doubts about the correct operation, or the safety of the product, please consult a specialist.
Controls and Parts
(1) Hour hand
(2) Normal position for the crown
(3) Crown position 1
(4) Crown position 2
Initial Start Up
In order not to discharge the battery during transport, the watch is provided with a crown stopper.
• Pull the crown into position 2 (4) and remove the crown stopper (a small plastic plate, which is clamped bet-
ween housing and crown).
• Press the crown back into the normal position (2).
• Your wristwatch is now ready for use.
Setting the time
• Pull the crown into position 2 (4), and set the current time by turning the crown. The second hand stops, in
order to allow the seconds to be set correctly.
• Press the crown back into the normal position (2).
Setting the date
• Pull the crown into position 1 (3), and set the current date by turning the crown.
• Press the crown back into the normal position (2).
If the date is set between 21:00 and 1.00, the date may not change the following day.
www.conrad.com
Version 03/10
(5) Date display
(6) Second hand
(7) Minute hand
Replacing the Battery
Keep batteries out of the reach of children.
Make sure that the polarity is correct when inserting the battery.
Remove the battery, if you are not going to use the watch for a while, to prevent damage
from leaking. Leaking or damaged batteries/rechargeable batteries can cause acid burns
°
upon contact with the skin. Thus, you should wear protective gloves when handling
damaged batteries.
Keep them out of the reach of children. Do not leave batteries lying around. There is the
risk that the batteries may be swallowed by children or pets.
Make sure that the battery is neither short-circuited nor thrown into a fire. Do not recharge
batteries. There is danger of explosion.
• If the watch stops, the battery needs to be replaced.
• Replacing the battery should be done by a specialist, using special watchmaker's tools and professional
knowledge.
• To replace the battery, the back of the casing is removed.
• The battery can then be removed from its holder and be replaced.
Water and Shock Resistance
In normal use, the wristwatch is protected against shocks. Nevertheless, do not expose the device to extreme
shocks such as might occur if the device falls on to a hard surface. This might damage the clockwork.
The indication 2 ATM indicates that the watch is suitably protected against hand washing, washing the car as
well as splashes and sweat.
It is not a diver's watch.
Maintenance and Cleaning
To clean the watch, a dry, soft and clean cloth is sufficient. For heavier soiling of the exterior, you can moisten
the cloth slightly with lukewarm water.
Clean the watch very carefully, otherwise you may scratch it.
Do not press too strongly on the glass cover as this may cause scratch marks.
Disposal
Please dispose of the product, when it is no longer of use, according to the current statutory
requirements.
Disposal of flat batteries/rechargeable batteries
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical Data
Voltage supply
Battery life
Weight
© Copyright 2010 by Conrad Electronic SE.
As the end user, you are required by law (Battery Ordinance) to return all used batte-
ries/rechargeable batteries; disposal of them in the household waste is prohibited!
Batteries / rechargeable batteries containing harmful substances are marked with the
following symbols, to indicate that disposal in the domestic waste is forbidden. The
symbols for the relevant heavy metals are: Cd = Cadmium, Hg = Mercury, Pb = Lead.
You can return used batteries/rechargeable batteries free of charge to any collecting
point of your local authority, to our stores or to any other store where batteries/rechar-
geable batteries are sold.
1.55V button cell SR626SW
approx. 2 years
40g
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.