Supplementary Information; Advanced Setup - Pioneer VSX-S520D Bedienungsanleitung

> Before Start > Part Names
Surround Set the low range capabilities for each channel by setting either
small or large.
"Small (Default Value)": For small speakers whose low range
capabilities may be limited
"Large": For full-range speakers with sufficient low range
capabilities
0 When "Front" is set to "Small", this is set to "Small".
0 If an item cannot be selected even though connection is
correct, check that the settings in "Configuration" - "Speaker
Channels" matches the number of connected channels.
Crossover When there are speakers that have been set to "Small", set the
Hz under which you would like other speakers to play bass, and
also set Hz under which you would like the LFE (low frequency
effect) to play the bass.
0 The value from "50Hz" to "200Hz" can be set. (Default Value
is "80Hz")
Double Bass This can be selected only when "Configuration" - "Subwoofer" is
set to "Yes" and "Front" is set to "Large".
Boost bass output by feeding bass sounds from the front left and
right, and center speakers to the subwoofer.
"On": Bass output will be boosted
"Off": Bass output will not be boosted
0 The setting will not automatically be configured even if you
performed Full Auto MCACC.
∫ Distance
Set the distance from each speaker to the listening position.
Front Left Specify the distance between each speaker and the listening
position. (Default Value is "10.0ft/3.00m")
Center Specify the distance between each speaker and the listening
position. (Default Value is "10.0ft/3.00m")
Front Right Specify the distance between each speaker and the listening
position. (Default Value is "10.0ft/3.00m")
50
> Install > Initial Setup > Playback

Supplementary information |

Height Left Specify the distance between each speaker and the listening
position. (Default Value is "10.0ft/3.00m")
Height Right Specify the distance between each speaker and the listening
position. (Default Value is "10.0ft/3.00m")
Surround Right Specify the distance between each speaker and the listening
position. (Default Value is "10.0ft/3.00m")
Surround Left Specify the distance between each speaker and the listening
position. (Default Value is "10.0ft/3.00m")
Subwoofer Specify the distance between each speaker and the listening
position. (Default Value is "10.0ft/3.00m")
0 Default values vary depending on the regions.
0 Distance units can be switched by pressing MODE on the remote controller. When the
unit is set as feet, you can set between 0.1 ft and 30.0 ft in increments of 0.1ft. When the
unit is set as meters, you can set between 0.03 m and 9.00 m in increments of 0.03 m.
∫ Channel Level
Front Left Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Center Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Front Right Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level (Default Value is "0 dB").
Height Left Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")
Height Right Select a value between "-12 dB" and "+12 dB" (in 1 dB
increments). A test tone will be output each time you change the
value. Select the desired level. (Default Value is "0 dB")

Advanced Setup

| Others
E
N