Overload Protection; Transporting Lithium Batteries; Maintenance - AEG BMMS18SBL Originalbetriebsanleitung

inside them. Corrosive or conductive fl uids, such as
seawater, certain industrial chemicals, and bleach or
bleach containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
This cut-off tool is intended to be used to cut diff erent
materials.
Do not use this product in any other way as stated for
normal use.
To reduce the risk of injury, only use Type "1" abrasive and
diamond wheels with a maximum 2,8 mm thickness, rated
with a maximum safe operating speed at least 20,000
min -1 . Type 1 wheels are for side grinding only, not surface
grinding. Read all safety information supplied with cut-off
wheels.
Use the chart below to choose the correct wheel. Different
types of wheels work best for different materials. Follow the
use recommendations from the wheel manufacturer.
Wheel Type
Carbide Abrasive
Wheel
Abrasive Cut-off wheel
Diamond Abrasive
Wheel

OVERLOAD PROTECTION

If the motor is overloaded, the overload protection will trip.
To continue working, switch the machine off and then on
again.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC and the following harmonized standards
have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-22:2011+A11:2013
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-06-30
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
22 ENGLISH
470 349 - BMMS18SBL.indd 22 470 349 - BMMS18SBL.indd 22
Recommended for Cutting
Drywall, Plastic
Steel, Stainless Steel,
Non-Ferrous Materials
Tile, Concrete, Brick,
Ceramics, Fiber Cement
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the
battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below
27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it
from being overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the
machine automatically. To restart, switch the machine off
and then on again. If the machine does not start up again,
the battery pack may have discharged completely. In this
case it must be recharged in the battery charger.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without
further requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding
experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice

MAINTENANCE

The ventilation slots of the machine must be kept clear at
all times.
Be sure to disconnect the tool from the power supply
before attaching or removing the saw blade.
Clean tool and guarding system with dry cloth. Certain
cleaning agents and solvents are harmful to plastics and
other insulated parts. Keep the apparatus handle clean, dry
and free of spilt oil or grease. Check the function of guards.
Regular maintenance and cleaning provide for a long
service life and safe handling.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been
described, please contact one of our AEG service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered.
Please state the machine type printed as well as the
six-digit No. on the label and order the drawing at your
09.06.2020 09:55:34 09.06.2020 09:55:34