Bosch Uneo Originalbetriebsanleitung Seite 14

14 | English
17 Charge connector
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Rotary Hammer
Article number
Rated voltage
Rated speed
Impact rate
Impact energy per
stroke according to
EPTA-Procedure 05/2009
Tool holder
Max. drilling dia.
– Concrete (with twist drill)
– Steel
– Wood
Weight according to
EPTA-Procedure 01:2014
Battery Charger
Article number
Charging time
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-6.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 60745-2-6:
Hammer drilling into concrete: a
Drilling into metal: a
Screwdriving without impact: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
1 609 92A 1FV | (3.8.15)
Downloaded from www.Manualslib.com
3 603 J52 0..
V=
-1
min
-1
min
J
SDS-Quick
mm
mm
mm
kg
2 607 225 463 (EU)
2 607 225 465 (UK)
2 607 225 641 (AU)
h
(triax vector sum) and uncertainty K
h
2
=20 m/s , K=1.5 m/s
h
2 2
=4.0 m/s , K=1.5 m/s
h
2
=2.5 m/s , K=1.5 m/s
h
manuals search engine
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" complies with all applicable
provisions of the directives 2011/65/EU, until 19 April 2016:
2006/95/EC, from 20 April 2016 on: 2014/35/EU, until
19 April 2016: 2004/108/EC, from 20 April 2016 on:
Uneo
2014/30/EU, 2006/42/EC including their amendments and is
in conformity with the following standards:
14.4
EN 60745-1, EN 60745-2-6 (battery powered product),
0–900
EN 60335-1, EN 60335-2-29 (battery charger).
0–4800
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9
70764 Leinfelden-Echterdingen, GERMANY
0.5
08
Henk Becker
Executive Vice President
10
Engineering
8
10
1.1
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 03.08.2015
Assembly
3
 Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
Battery Charging (see figure A)
 Do not use other battery chargers. The supplied battery
charger is designed for the Lithium-Ion battery in your ma-
chine.
 Observe the mains voltage! The voltage of the power
2
supply must correspond with the data given on the name-
2
. plate of the battery charger. Battery chargers marked with
230 V can also be operated with 220 V.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Bosch Power Tools