Bosch GSK 18 V-LI Professional Originalbetriebsanleitung Seite 12

OBJ_BUCH-1335-005.book Page 12 Tuesday, November 11, 2014 11:28 AM
12 | English
Service
 Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is main-
tained.
Safety Warnings for Cordless Tackers
 Always assume that the tool contains fasteners.
Careless handling of the tacker can result in unexpected
firing of fasteners and personal injury.
 Do not point the tool towards yourself or anyone
nearby. Unexpected triggering will discharge the fas-
tener causing an injury.
 Do not actuate the tool unless the tool is placed firm-
ly against the workpiece. If the tool is not in contact
with the workpiece, the fastener may be deflected away
from your target.
 Disconnect the tool from the power source when the
fastener jams in the tool. While removing a jammed
fastener, the tacker may be accidentally activated if it is
plugged in.
 Use caution while removing a jammed fastener. The
mechanism may be under compression and the fasten-
er may be forcefully discharged while attempting to free
a jammed condition.
 Do not use this tacker for fastening electrical cables.
It is not designed for electric cable installation and may
damage the insulation of electric cables thereby causing
electric shock or fire hazards.
 Use appropriate detectors to determine if utility
lines are hidden in the work area or call the local util-
ity company for assistance. Contact with electric lines
can lead to fire and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water line causes
property damage.
 Observe the conditions of the job site. It is possible
that fasteners can burst through thin workpieces or be
deflected when working in corners or against edges,
and harm persons.
 When working, hold the power tool in such a manner
that your head and body cannot be injured in case of
sudden kickback due to a malfunction of the energy
supply or from hard objects/locations in the work-
piece.
 Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g.,
against continuous intense sunlight, fire,
water, and moisture. Danger of explosion.
Downloaded from www.Manualslib.com
Product Features
The numbering of the product features refers to the illus-
tration of the machine on the graphics page.
1 Workpiece protector
2 Discharge lock-off
3 Clamping lever for opening/closing the shot duct
4 Thumbwheel for depth stop adjustment
5 Switch for blocking the actuation system
6 Trigger
7 Battery unlocking button
8 Battery pack
9 Handle (insulated gripping surface)
10 Storage for workpiece protector
11 Belt hook
12 Magazine
13 Magazine slider
14 Nail pusher
15 Outlet
16 Nail strip*
17 Magazine spring
*Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accesso-
ries can be found in our accessories program.
Technical Data
Cordless nailer
Article number
Rated voltage
Actuation system
– Single actuation with safety
run
Fastener
– Type
– Length
– Diameter
– Angle
Magazine capacity, max.
Operating duration with 3.0 Ah
battery pack (continuous opera-
tion)
Dimensions
– Height
– Width
– Length
Weight according to
manuals search engine
differ. This may significantly increase the exposure level
over the total working period.
An estimation of the level of exposure to vibration should
also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This
may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and
the accessories, keep the hands warm, organisation of
work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product
described under "Technical Data" is in conformity with all
relevant provisions of the directives 2011/65/EU,
2014/30/EU, 2006/42/EC including their amendments
and complies with the following standards:
EN 60745-1, EN 60745-2-16.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
GSK 18 V-LI
Robert Bosch GmbH, Power Tools Division
3 601 D80 3..
70764 Leinfelden-Echterdingen, GERMANY
V= 18
Leinfelden, 13.11.2014
Assembly

Battery Charging
 Use only the chargers listed in the technical data.
Brads
Only these chargers are matched to the lithium-ion bat-
mm 32–64
tery of your power tool.
mm 1.6
20° Note: The battery supplied is partially charged. To ensure
full capacity of the battery, completely charge the battery
105
in the battery charger before using your power tool for the
first time.
approx. 700
The lithium-ion battery can be charged at any time without
nails
reducing its service life. Interrupting the charging proce-
dure does not damage the battery.
mm 295
The "Electronic Cell Protection (ECP)" protects the lithium-
mm 96
ion battery against deep discharging. When the battery is
mm 334
discharged, the power tool is switched off by a protective
circuit: Fasteners can no longer be shot.
Helmut Heinzelmann
Head of Product Certification
PT/ETM9