Makita CL072D Bedienungsanleitung Seite 7

To insert the battery cartridge, hold it so that the
•
battery cartridge front shape fits to that of the battery
installment opening and slip it into place. Always
insert it all the way until it locks in place with a little
click. If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
Do not use force when inserting the battery
•
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
Battery protection system
The cleaner is equipped with the protection system, which
automatically cuts off the output power for its long service life.
The cleaner stops during operation when the cleaner
and/or battery are placed under the following situation.
This is caused by the activation of protection system and
does not show the cleaner trouble.
When the cleaner is overloaded:
•
At this time, release the switch trigger and
remove causes of overload and then pull the
switch trigger again to restart.
When the remaining battery capacity gets low:
•
Recharge the battery cartridge.
Switch action
Fig.3
To start the cleaner, simply press the "HIGH/LOW" button.
To switch off, press the "OFF" button. To change the
cleaner speed, press the "HIGH/LOW" button. The first
press on this button is for high speed and the second
press for low speed and then each press on this button
repeats the high/low speed cycle alternatively.
Battery power lamp
Fig.4
When the remaining battery capacity gets low, the
•
battery power lamp blinks.
When the remaining battery capacity gets much lower,
•
the tool stops during operation and the battery power
lamp lights up for about ten seconds. At this time, remove
the battery cartridge from the tool and charge it .
NOTE:
The time at which the battery power lamp start
•
blinking or lighting up depends on the temperature
at work place and the battery cartridge conditions.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Disposing of Dust
CAUTION:
Empty the cleaner before it becomes too full, or the
•
suction force weakens.
Downloaded from www.Manualslib.com manuals search engine
Be sure to empty out the dust inside the cleaner
•
itself. Failure to do so may cause the sponge filter
to be clogged or the motor to be damaged.
Never throw away the dust stopper because it
•
should be used whenever either the dust bag or the
dust pack is used.
Fig.5
1. Push the button to open the front cover. Opening it
until a click is heard allows a positive stop at that
position.
Fig.6
NOTE:
The cleaner is constructed in such a way that the front
•
cover comes off when trying to force the front cover
open at the angle of more than 90°. If the front cover
comes off, insert it into the front cover joint in place.
CAUTION:
When closing the front cover, be careful not to
•
pinch your fingers.
Fig.7
2. Pull out both the orange-colored dust stopper and
dust bag together at the same time.
Fig.8
Fig.9
3. Remove the dust stopper and empty the cleaner.
Dust bag and paper pack
Install either dust bag or paper pack before using cleaner.
Use the dust stopper when installing either dust bag or
paper pack.
Dust bag are usable many times repeatedly by cleaning it out.
Paper pack is a throw-away type. Throw away the entire
paper pack without emptying when it has become full.
Installing dust bag
Fig.10
Use the dust stopper when installing dust bag. Be careful
not to take the upper side for the lower side by mistake
because they are different each other.
Fig.11
1. Insert the protrusion of the dust bag into the
groove in the dust stopper as shown in the figure.
Fig.12
2. There is no distinction between the upper and
lower sides of the dust bag. You may insert its
protrusion of any side into the lower groove of the
dust stopper.
Fig.13
3. Overlap the frame of dust stopper with that of the
dust bag.
Fig.14
4. Place the dust stopper and the dust bag together
into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way
into the slots in the cleaner cavity.
7