Warranty - Leatt 3DF AIRFIT LITE BODY VEST Anleitung

Marking and labeling
The following diagrams provide important information about this product and the protection it provides.
The "CE " mark denotes
compliance with the health
and safety requirements of
Annex II of the European
Personal Protective Equipment
Regulation 2016/425.
The recommendation to
read the manufacturer's
instructions contained in
this booklet
Cleaning
Always follow the washing instructions printed on the label attached to the garments, since when alternative
fabrics with specific performance characteristics are used, washing instructions may differ. Touch-and-close
fastenings, where fitted, can be cleared of debris using a nail brush. If the protector components have become
soiled in use, wipe the surface with a damp cloth. Use a soft brush, damped in water, to clean the perforations
in the components. Only use tap water. Never use cleaners or detergents, or launder the protector, the
product will be damaged by the cleaning process and chemicals and the level of protection provided severely
reduced.
Common substances applied to this product (solvent, cleaners, hair tonics, etc.) can cause damage that may
be invisible to the user and compromise the effectiveness/safety of your Leatt ® product. If in any doubt,
please contact the manufacturer before cleaning or laundering your protector. Always refer to the material
content label on the Leatt ® product. None of the materials used in the construction of the product are known
to contain anything that is harmful or might cause an allergic reaction or be dangerous to health.
Cold wash No bleach Dry in shade
Storage and transportation
Place the Leatt ® product on a clean, dry surface and store in a dry, well-ventilated environment away from
direct sunlight and extreme temperature. Do not place heavy objects on top of Leatt ® product as this can
damage the fabrics and plastic materials. The protection provided by your Leatt ® product should not be
affected by non-extreme ambient temperature and weather conditions.
6
Denotes that the product
is or incorporates a chest
protector, assessed as size
Type A, which meets level
1 of European Standard
prEN 1621-3:2013
Denotes that the product
is or incorporates a back
protector ("CB") which
meets level 1 of European
CB
Standard EN 1621-2:2014
1
No tumble dry Do not iron No solvents
Copyright © 2016, Leatt ® Corporation
Maintenance and obsolescence
For maximum performance, the Leatt ® product must be inspected prior to each use. Stop using the protector
if any components show signs of damage or are worn, cracked, and/or deformed, or if the inside padding
has deteriorated. Leatt ® Corporation recommends that the Leatt ® product is replaced every three (3) years
under normal use conditions. Should you experience a collision or if the Leatt ® product or any component
shows any signs of damage, cracking, deformity and/or the inside padding is deteriorating, return the product
to the seller for inspection or destroy and replace it. Please dispose of it in an environmentally-friendly
manner. Do not drill holes, paint, cut, heat, bend, apply decals or stickers, or make any other modifications to
the elbow guard. Doing so may compromise the effectiveness and safety of your Leatt ® product.
Use with other Personal Protective Equipment
Leatt ® protectors form part of a protective equipment ensemble available for use by participants in off-road
motorcycling and downhill biking activities. Additional PPE, which it is recommended should be worn during
off-road motorcycling and downhill biking activities, includes clothing conforming to EN 13595-1:2002, where
applicable to the riding environment (may not be suitable for off-road motorcycling or downhill cycling) or
other suitable clothing providing full coverage to the body, arms and legs; impact protectors conforming to EN
1621-1:2012 (where not already a component of your Leatt ® protector or other motorcycle clothing); gloves
conforming to EN 13594:2002; boots conforming to EN 13634:2010. Always perform any motor sport activity
with caution and use/wear appropriate safety equipment.
Contact details
Head Office:
No 50, Kiepersol Crescent, Atlas Gardens, Contermanskloof, Durbanville, 7550,
Cape Town, South Africa
Tel: +27 21 557 7257 | Fax: +27 21 557 7381
Email: info@leatt.com | Website: www.leatt.com
Postal Address:
Suite 109, Private Bag X3, Bloubergrant, 7443, South Africa
USA:
Tel: 661 287 9258 | Toll Free: 1.800.691.3314 | Fax: 661 287 9688
Europe:
Email: Leatt-EU-contact@leatt.com
Your Leatt ® product is warranted to be free of defects in materials or manufacturing for one year from
date of purchase. Your Leatt ® product may break under certain conditions of use, so damage caused by
accidents, falls, abuse or misuse is not covered by this limited warranty.
To make a warranty claim, go to www.leatt.com or send an email to warranty@leatt.com.
LEATT ® CORPORATION EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Copyright © 2016, Leatt ® Corporation

WARRANTY

GB
7