Specifications - Makita BFR540 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Red part
1-2. Button
1-3. Battery cartridge
2-1. Lever
2-2. Stopper base
2-3. Label on feeder box
2-4. Fenestella
3-1. Stopper base
3-2. Casing
3-3. Adjusting knob
4-1. Switch trigger
5-1. Reversing switch lever

SPECIFICATIONS

Standard battery cartridges
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Noise
The typical A-weighted noise level determined according
to EN60745:
Model BFR540
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Model BFR550
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Model BFR750
Sound pressure level (L
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Downloaded from www.Manualslib.com
6-1. Casing
6-2. Thumb screw
7-1. Plane bearing
7-2. Dust cover
7-3. Bit
8-1. Feeder box
8-2. Screw strip
8-3. Screw guide
9-1. Driving position
11-1. Reverse button
13-1. Hook
15-1. Wall
Model
Screw strip
-1
No load speed (min )
Overall length
Net weight
Rated voltage
) : 77 dB(A)
pA
) : 78 dB(A)
pA
) : 76 dB(A)
pA
Wear ear protection
manuals search engine
Explanation of general view
BFR540
4 x 25 - 55 mm
424 mm
2.0 kg
D.C. 14.4 V
BL1430
ENE033-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
ENG905-1
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
•
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
•
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
4
15-2. Stopper base
16-1. Limit mark
17-1. Casing
17-2. Thumb screw
18-1. Front cover
18-2. Screws
19-1. Spring
19-2. Arm
19-3. Recessed part
20-1. Carbon brush cap
21-1. Hole
21-2. Carbon brush cap
BFR550 BFR750
4 x 45 - 75 mm
4,000
464 mm
2.1 kg 2.1 kg
D.C. 18 V D.C. 18 V
BL1830
2
) : 2.5 m/s or less
h
2
ENG900-1
ENG901-1