cam LINEA Handbuch Seite 29

overload the basket with more than 2kgs.
8. POSSIBLE COMBINATIONS:
The diagram shows the age/weight for the use of
the various features and their correct assembly.
The carrycot and car seat are provided with the
special quick fastening and removal system called
"quicky System". The pushchair is reversible: it can
be fitted on the chassis both rear facing so the seat
is facing Mum or Dad or forward facing so the seat
looks towards the road (Via vai System Reverse).
9. HOW TO REMOVE THE SEAT UNIT
9a. Unfasten flaps from armrests.
9b. Lift up and grab the 2 handles "F" placed on
both sides of the seat unit.
9c. Push first button "A" then "B" located
underneath the handles.
9d. Remove the seat unit from the main chassis
and keep it for future use.
9e. Fasten flaps to the armrests.
9f. ATTENTION! Do not fit/release the seat unit
when the baby is seated.
HOW TO FIT & REMOVE THE CARRYCOT FROM
THE CHASSIS:
10. Pull out the metal flaps D under the carrycot
to lock them in the housing "E" until a clack is
heard.
Make sure the carrycot is securely and safely
locked.
11. To remove the carrycot press down on button
"A", followed by button "B" on the pushchair
armrests. Whilst still holding down button "B"
remove the carrycot from the chassis.
12. USING THE CARRYCOT
12a. To fasten the hood to the carrycot, insert the
metal tabs into the slots at the sides of the handle.
Close the press fasteners on the back of the hood.
12b. By opening the flaps located under the body,
the carrycot converts into a rocking cot.
12c. The angle of the handle can be adjusted by
pressing the buttons at the sides of the handle at
the same time (safety mechanism).
12d. Aerated base.
12e. To raise the backrest, push the handle located
underneath inwards towards the body. To lower it,
press the handle slightly inwards, lift it and move
it back to the required position.
12f. To fit the footmuff, close the press fasteners
as shown in the diagram.
12g. The hood is adjustable in height.
12h. To remove the hood, release the ends of the
metal tabs.
AUTO KIT V483 (OPTIONAL EXTRA, EXCEPT IN
THE UK)
13a. Auto kit.
13b. Impact protection padding.
13c. Fitting the abdominal restraint system. Insert
the two buckles "A" inside the slots situated within
the base of the carrycot, as shown in the sequence
of illustrations. WARNING! Be sure to verify that
the abdominal belt is fitted correctly to the base of
the carrycot and that buckles "A" are flat up
against the underside of the carrycot as shown in
illustration 3.
13d. How to adjust the abdominal belt.
13e. The Correct fitting of Auto kit belts "D" to the
INSTRUCTIONS FOR USE
Vehicle seat belts "C". Ensure that the Auto kit
belts are fitted to the lowest point possible to the
vehicle seat belt, in contact with the base of the
vehicles seat.
13f. Fixing and tightening the Auto kit belts.
13g. The correct positioning of the carrycot.
HOW TO FIX AND RELEASE THE CAR SEAT FROM
THE CHASSIS
14a. Place the car seat on the pushchair armrests
in proximity of the attachment housing "E". Push
the car seat down until it clicks into position. Verify
that the car seat is securely and safely locked into
position.
14b. To remove the car seat press down on button
"A", followed by button "B" on the pushchair
armrests. Whilst still holding down button "B"
remove the car seat from the chassis.
FITTING AND ADJUSTMENT OF THE 5-POINT
HARNESS:
15a. WARNING! Before fitting the belts, look
carefully at the diagram to check that the seat
fastening systems correspond correctly with: the
shoulder belts ("s" with "S1" or "S2"), the waist belt
("a" with "A") and the crotch strap ("g" with "G1 or
"G2"). WARNING! Choose the correct slots
according to the age and size of the baby: "G1"
and "S1" from 0 to 6 months, "G2" and "S2" from
6 to 36 months.
0-6 MONTHS:
15b. FITTING THE SHOULDER BELTS: insert the
buckles "s" into slots "S1". WARNING! All the
buckles must be passed through the material slots
and the rigid structure of the backrest in order to
be inserted correctly, as shown in the diagrams.
15c. FITTING THE WAIST BELT: insert buckles "a"
in slots "A".
15d. FITTING THE CROTCH STRAP: insert buckle
g" in "G1".
WARNING! Before use, check that the belts are not
twisted and that they are secured properly.
15e. CORRECT FITTING OF THE BELTS: Fasten
the belt, make sure that the two hooks are fixed
inside the main buckle and check that the baby's
legs are positioned one either side of the crotch
strap.
15f. Belt adjustment.
15g. Opening the buckles.
WARNING! Always use the 5-point safety harness.
16. REMOVING THE BELTS: Remove the belts as
shown in the diagram.
6-36 MONTHS:
17. Fit the 5-point harness taking care that
buckles "s" correspond with "S2" and buckles "g"
with "G2"(see point 15a).
18. FITTING THE SEAT REARWARD FACING
(0-12 months):
Unfasten the buttons.
Grab the handles "F", place the seat unit on the
frame as shown in the picture and push
downwards until you hear a "click". Fasten the
flaps.
ATTENTION! Do not fit/release the seat unit when
the baby is seated.
19. HOW TO USE THE BUMPER BAR: turn
outwards parts "Y" and insert the bumper bar in its
27