Stanley J309E Anweisunghandbuch Seite 4

FEATURES
1. USB power button
2. USB power port (under protective cover)
3. 12 VDC accessory socket (under protective cover)
4. USB power indicator
5. Battery status LED indicators
6. Reverse polarity indicator
7. Jump-starter on/off switch
8. Pivoting LED area light
9. Battery power level button
10. Pivoting LED area light power switch
11. DC charging socket
12. Positive (+) red clamp
13. Negative (–) black clamp
14. Mains charging adapter
15. 12V DC charging adapter (optional accessory)
CHARGING THE UNIT
This unit is shipped in a partially charged state.
• Charge the unit before first use using the mains charging adapter for 24 hours.
Lead-acid batteries require routine maintenance to ensure a full charge and a long battery life. All batteries lose energy from self-discharge
over time and more rapidly at higher temperatures. When the unit is not in use, manufacturer recommend that the battery is charged at least
every 30 days.
• Check the battery charge level by pressing the battery status pushbutton. The LED charge status display will indicate the level of battery
charge. When only one red LED lights, charge the unit.
• Make sure all other unit functions are turned off during recharging, as this can slow the recharging process.
Note:
Charging the battery after each use will prolong the battery life; frequent heavy discharges between charges and/or overcharging will reduce battery life.
Important! When the battery is overly discharged and if the green LED is lit when the charger is plugged in, this indicates the battery is at a
high impedance stage. In this event, recharge the unit and leave the unit charging for a period of 24 hours before use.
Charging the unit using the mains charging adapter
• Insert the jack of the appropriate mains charging adapter (either the EU model or the GB model) into the DC charging socket on the back of
the unit.
• Insert the appropriate mains charging adapter plug into a mains power socket.
• Charge until two red and one green (full) battery status LEDs light or flash.
• Continue to charge for one to two more hours.
• Once fully charged disconnect the mains charging adapter from the mains power socket and then remove the jack plug of mains charging
adapter from the DC charging socket on the back of the unit. Store it in a safe place.
12 volt DC charging method (optional accessory)
Charging the unit from an external 12 volt DC power source requires the use of the 12V DC charging adapter. This adapter has a male DC
connector at each end.
1. Insert the 12 volt DC charging adapter plug with the grooved tip into the vehicle's 12V DC accessory outlet or other 12 volt DC power
source.
2. Insert the other end plug into the 12 volt DC accessory outlet on the front panel of the unit.
3. Charge the unit until the green FULL indicator lights when the battery power level button is pressed (with the adapter unplugged from the
unit). DO NOT CHARGE MORE THAN 6 HOURS MAXIMUM USING THIS METHOD.
4. When charging is complete, remove the charging cord and store in a safe place.
Notes:
Some vehicles require that the ignition be switched to the accessory outlet position in order to power the accessory outlet.
DO NOT LEAVE THE UNIT UNATTENDED WHEN CHARGING USING THE THIS METHOD.
USE
Using the unit as a jump-starter
Warning! Make sure that the vehicle is in neutral with the parking brake applied.
Note:
If your connections are incorrectly made, the unit will beep continuously and the red reverse polarity indicator will illuminate, even if the on/off switch is in
the off position. Rectify the connections immediately.
Warning! Make sure that the cables are not in the path of moving belts or the fan.
1. Turn off the vehicles ignition and all accessories before making any connections.
2. Make sure that the jump-starter on/off switch is turned off.
3. The following procedure is for a negative earth system ie the negative battery terminal is connected to the chassis.
ENGLISH
J309E_Manual_100716.indd 6-7
6
4. Connect the positive (+) red clamp to the vehicle's positive battery terminal.
5. Connect the negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or chassis part. Never clamp directly to
negative battery terminal or moving part. Refer to the automobile owner's manual.
6. Turn the jump-starter on/off switch to the on position.
7. Start the vehicle and crank the engine in 3 to 6 second bursts.
Important! If the engine doesn't start within 6 seconds let the units internal battery cool for 3 minutes before making another attempt.
8. When the vehicle starts, turn the jump-starter off/on switch to the off position.
9. Leave the vehicle's engine running.
10. Disconnect the (–) black clamp connected to the engine or chassis first, followed by the (+) red clamp that is connected to the battery
positive (+) terminal.
11. Carefully press the negative (black) jumper cable wire into the storage channel starting at the end furthest from the clamp.
12. Clamp the negative (black) clamp onto the clamp holder.
13. Carefully press the positive (red) jumper cable wire into the storage channel starting at the end furthest from the clamp.
14. Clamp the positive (red) clamp onto the clamp holder.
15. Charge the unit as soon as possible.
16. Make sure that the jump-starter on/off switch is turned off while the unit is being charged or stored.
Using the pivoting LED area light
The pivoting area light is controlled by the area light power switch on top of the light. Make sure the area light is turned off when the unit is
being recharged or stored.
Using the USB socket
1. Push the USB power button to turn the USB port on. The USB power indicator will light.
2. Lift up the cover of the USB socket.
3. Plug the USB-powered device into the USB socket and operate normally.
Notes:
This unit's USB socket does not support data communication. It only provides 5 volts/2A DC power to an external USB-powered device.
Make sure the USB power button is in the off position when the unit is being recharged or stored.
Some household USB-powered electronics will not operate with this unit.
Using the 12V DC power socket
This portable power source is also for use with all 12 volt DC accessories equipped with a male accessory socket plug and are rated up to 5
amps.
1. Lift up the cover of the unit 's 12V DC socket.
2. Insert the 12 volt DC plug from the appliance into the 12V DC accessory socket on the unit. DO NOT EXCEED A 5 AMP LOAD.
3. Switch on the appliance and operate as usual.
4. Periodically press the battery power level button to check battery status.
TROUBLESHOOTING
Unit will not charge
• Make sure the power switch is in the off position.
• Make sure the jack of the mains charging adapter is properly connected to both the unit and a functioning mains power socket. OR
• Make sure the 12V DC charging adapter is properly connected to both the unit and a functioning DC power source.
Unit Fails to Jump-Start
• Make sure unit's power switch is in the on position.
• Check that jump-starter has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
USB Power Port will not power appliance
• Make sure the USB charging port power button is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
LED Area Light does not come on
• Make sure the Pivoting LED area light power switch is in the on position
• Check that unit has a full charge. Recharge unit if necessary.
12 volt DC accessory socket will not power appliance
• Make sure the the appliance does not draw more than 5 amps.
• Check that unit has a full charge. Recharge unit if necessary.
7
10/7/2016 11:47:53 AM
ENGLISHn