Bosch GBH 2600 Professional Originalbetriebsanleitung Seite 14

14 | English
Technical Data
Rotary Hammer
Article number
Speed control
Stop rotation
Right/left rotation
Quick change chuck
Rated power input
Impact frequency at rated speed
Impact energy per stroke according
to EPTA-Procedure 05/2009
Rated speed
Tool holder
Spindle collar diameter
Drilling diameter, max.:
– Concrete
– Brickwork (with core bit)
– Steel
– Wood
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 91 dB(A); Sound power level
102 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 60745:
Hammer drilling into concrete: a
Chiselling: a =14 m/s
h
Drilling in metal: a
Screwdriving without impact: a
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
1 619 929 K34 | (28.10.11)
Downloaded from www.Manualslib.com
Professional
0 611 254 8..
W
-1
min
J
-1
min
mm
mm
mm
mm
mm
kg
(triax vector sum) and uncertainty K
h
2
=15 m/s , K=1.5 m/s
h
2 2
, K=1.5 m/s ,
2 2
<2.5 m/s , K=1.5 m/s ,
h
2
<2.5 m/s , K=1.5 m/s
h
manuals search engine
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
GBH 2600
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
720
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
4000
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
2,7
Senior Vice President
900
Engineering
SDS-plus
50
26
Robert Bosch GmbH, Power Tools Division
68
D-70745 Leinfelden-Echterdingen
13
Leinfelden, 28.10.2011
30
Assembly
2,9
Before any work on the machine itself, pull the mains
/II
plug.
Auxiliary Handle
Operate your machine only with the auxiliary handle
14.
Changing the position of the auxiliary handle
(see figure A)
The auxiliary handle 14 can be set to any position for a secure
and low-fatigue working posture.
– Turn the bottom part of the auxiliary handle 14 in counter-
clockwise direction and swivel the auxiliary handle 14 to
the desired position. Then retighten the bottom part of the
auxiliary handle 14 by turning in clockwise direction.
2
,
Pay attention that the clamping band of the auxiliary handle is
positioned in the groove on the housing as intended for.
2
Adjusting the Drilling Depth (see figure B)
The required drilling depth X can be set with the depth stop
13.
– Press the button for the depth stop adjustment 12 and in-
sert the depth stop into the auxiliary handle 14.
The knurled surface of the depth stop 13 must face down-
ward.
– Insert the SDS-plus drilling tool to the stop into the SDS-
plus tool holder 3. Otherwise, the movability of the SDS-
plus drilling tool can lead to incorrect adjustment of the
drilling depth.
– Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop correspond with
the desired drilling depth X.
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
Bosch Power Tools