Grundig EC 4600 RDS Serviceanleitung Seite 9

v
Possible settings ...
Activating coding (for details, see the
chapter "Coding", page 16).
CODE
If " " appears in the display, coding is
not activated.
SAFE
If " " appears in the display, coding is
activated.
Display brigthness
DISPL 07
" " (00 ... 07). Set according to
the location of the car radio so
that the display can optimally
be read off.
If you havec connected the car radio to
the illumination contact of the vehicle's
plug connector, the display brightness will
change if the headlights of the vehicle are
switched on (night setting) or off (day
setting). Both settings can separately be
selected and stored in memory with
switched on or switched off headlights.
Coding
Your personal code number is on the iden-
tity card of your car radio.
Coding is not activated when the radio lea-
ves the factory.
If you have "activated" your car radio's
coding: As soon as you disconnect the car
radio from the car battery (or permanent
plus terminal 30), it is electronically
blocked.
Only you are able to put it back into opera-
tion by entering your personal Code Number.
Is the coding activated?
Activate the EXPERT mode and turn the
¢ ¢
left-hand control knob until the display indi-
SAFE CODE
cates " " or " ".
Coding activated.
Coding not activated.
Downloaded from www.Manualslib.com
EXPERT control level
LRN ON
" ": autom. LEARN
Security LED (on/off)
LRN OFF
" ": no autom. LEARN wished.
BLK ON
" " The Security LED flashes if
the radio and the ignition are
If the volume is set below "
LRN ON
switched off.
" " setting is supposed.
BLK OFF
" " The Security LED does not flash.
Autom. change of regional programme
Sound signal (on/off)
If an RDS programme consists of various
BEEP ON
regional programmes, it may occur that
" " Sound signal as function con-
your car radio changes between regional
firmation.
BEEP OFF
stations when changing the reception area.
" " Function confirmation
through brief muting of the
REG ON
" " autom. change of regional
loudspeaker outputs.
programme is possible.
REG OFF
" " no change of regional
AM range (on/off)
programme is possible.
AM ON
" " The AM range can be selected
with the ¢ ¢ button.
RADIO
Switching on and off with the
AM OFF
ignition/start switch
" " The AM range is skipped when
IGN ON
" " It is possible to switch the radio
switching between ranges.
on and off with the ignition/start
Autom. LEARN (radio mode) switch of the vehicle.
IGN OFF
" " Switching on and off is only
If you are in a reception area in which
possible with the
reception of RDS programmes with traffic
announcements is poor, you can disable
the autom. LEARN function in radio mode.
Activating the coding Deactivating coding
1. Select the EXPERT control level and turn before removing the car radio, for example.
CODE
¢ ¢
the right-hand control knob until " "
1. The EXPERT mode must be switched on
appears in the display.
SAFE
and " " indicated in the display.
Activate the change mode:
Activate the change mode:
Briefly press the right-hand ¢ ¢ control
Briefly press the right-hand
CH - - - -
knob. The display indicates " "
knob. The display indicates "
(CH = Change).
(CH = Change).
2. Enter the code number (on the Identity
2. Enter the code number (on the Identity
Card): Use the right-hand ¢ ¢ control knob
Card) by turning the right-hand
to enter the correct number.
knob as described under "Activating
¢ ¢ Coding"
When the right-hand control knob is
turned quickly, it will function like a
3. Confirm the code number:
flywheel.
Press the right-hand
CODE
" " appears briefly in the display.
3. Confirm the code number:
Briefly press the right-hand ¢ ¢ control knob. The radio will play after approximately
SAFE
3 seconds.
" " appears in the display.
Coding is activated! Coding is deactivated!
4. Deactivate the EXPERT control level: If you have entered the incorrect code
Press the ¡ button or the right-hand number:
SAFE
¢ ¢ " " remains in the display and the radio
control knob until the signal sounds.
does not play.
Begin again. Be sure to observe the waiting
periods between attempts (see page 17).
manuals search engine
Muting in telephone mode
PHONE ON
"
PHONE OFF
VOL 4 "
", the
m
MCD and AUX input sensitivity
to adjust the sensitivity to a CD changer.
MCD LOW
" " low
MCD MID
" " medium
MCD HIGH
" " high
Volume limitation when switching on
ON VOL - -
"
ON VOL 20
"
The volume is limited only if the volume
when the car radio is switched off is
greater than the set value!
Minimum volume for traffic
announcements
TA VOL 16
" " (5 ... 46)
¡ button.
IO
The volume for the traffic announcement
can be heard during setting.
Return to operation
With coding activated, the car radio is electro-
nically disabled after it has been disconnected
from the car battery (or permanent plus, ter-
minal 30), e.g. after the radio has been remo-
ved during servicing.
¢ ¢ control
CH 1 - - - -
" 1. Switch on the car radio.
The display indicates "
After approx. 3 seconds, the display indi-
I - - - -
cates "
¢ ¢
control
number of attempts).
2. Enter the code number (on Identity Card),
by turning the right-hand
as described in the chapter "Activating
¢ ¢
control knob until
coding".
3. Confirm the code number:
Press the right-hand
SAFE
" " appears briefly in the display.
After approximately 3 seconds the radio
will play.
If you have entered the incorrect code
number:
SAFE
" " remains in the display and the radio
does not play.
Begin again. Be sure to observe the waiting
periods between attempts.
u
Speed controlled volume
" Muting activated. " SCVOL 20 " (- - ... 69)
" Muting deactivated. The adjustment is only possible if a speed-
controlled signal is present at the SCV
connection (A1).
SCVOL - -
" " : SCV de-activated
SCVOL 69
" " : maximum effect.
í
(eg. MCD 36/MCD 40) For reasons of safety, the following
setting should be carried out by the
passenger!
Setting:
": no limitation
1. Car standing still, motor running:
": max. volume, eg., 20
set desired volume with the left-hand
(- - ... 46).
control knob.
2. Prepare EXPERT setting:
press the ¡ button until the signal
sounds.
Turn the right-hand ¢ ¢ control knob until
SCVOL ...
" " appears in the display.
Briefly press the right-hand ¢ ¢ control
knob:
CH
The display indicates " "
3. At higher speed:
set desired volume with the right-hand
SCVOL 53
¢ ¢ control knob, e.g. " " in dis-
¢ ¢
play. Press the right-hand control knob
until the signal sounds.
Waiting periods
To prevent deactivation of the coding being
possible by trial and error, waiting periods are
required between attempts. During these wait-
ing periods, the car radio can be switched on
and off but will not play.
During the waiting period
SAFE
". the car radio needs not be switched on, but
it must be connected to the permanent +12 V
I
". (The " " stands for the voltage. As long as the display indicates
SAFE
" ", the waiting period has not yet elapsed.
The waiting period is over when the number
of the next attempt is visible in the display,
¢ ¢ control knob
2 - - - -
e.g. " ".
¢ ¢ control knob until
EXPERT control level
{
CLOCK ON/OFF
CLOCK ON
" " Time indication on.
CLOCK OFF
" " Time indication off.
i
Clock synchronization
sync ON
" " The built-in clock is
synchronized by RDS
signals.
sync OFF
" " In areas where no RDS
TIMER signals are received,
the synchronization func-
tion can be deactivated.
v
DIGITIME
TM 00:00
" " This function serves for
manual time setting. If you
turn the right-hand control
knob quickly, it will act as a
flywheel.
i
sync ON
If " " has been selected (see ),
the manually set time may be corrected
by the currently received RDS station.
If this RDS station should transmit an
undesired time, you must disable this
sync OFF
correction by selecting " ".
Coding
The table shows the waiting periods between
the individual attempts.
Waiting period after the 7th attempt is always
24 hrs!
After the 6th attempt we recommend having a
dealer complete the "Return to operation" or
"Deactivate coding" process.
Attempt Wait.per.
(in display) (approx.)
1
21 sec.
2
1.5 min.
3
5.5 min.
4
22 min.
5
1.5 hrs.
6
6.0 hrs.
7
24 hrs.
8
24 hrs.