Garant INFO POINT Betriebsanleitung Seite 12

GARANT INFO Point, computer desk, computer workstations
7.2.5. Computer
1. Put computer on pedestal in rear.
2. Connect monitor, keyboard and mouse to computer. Observe
computer manual.
en
7.3. COMPUTER WORKSTATIONS
7.3.1. Monitor
i
Article no. 948101, 948121, 948122, 948251, 948261, 948252,
948262: Maximum monitor size (W×H): 690 mm × 460 mm.
Article no. 948111, 948112: For 19-inch CRT monitor.
1. Unlock and open the monitor housing.
2. Remove the cap in the bamboo board and use a screwdriver to
push out the punch-out in the cap.
3. Route monitor cables downwards.
4. Place monitor into monitor housing and connect cables.
5. Proceed with Mouse and keyboard [} Page 12].
7.3.2. Mouse and keyboard
i Applies to: Article no. 948111 – 948262.
1. Unlock and open panel for keyboard and mouse.
2. Remove the cap in the panel and use a screwdriver to push out
the punch-out in the cap.
3. Put mouse and keyboard in position.
4. Route the cables downwards through the cable pass-throughs
in panel and casing.
5. Route cable through caps and insert caps in panel and casing.
7.3.3. Printer
1. Place printer on retractable shelf.
2. Route cables to the rear of the retractable shelf and out through
the cable pass-through.
7.3.4. Computer
1. Unlock and open cabinet compartment for computer.
2. Put computer inside.
» Ensure adequate circulation of air. Observe gap between fan
and wall.
3. Connect monitor, keyboard, mouse (and printer of applicable)
to computer. Observe computer manual.
4. Remove the cap in the casing's rear and use a screwdriver to
push out the punch-out in the cap.
5. Route out the required cables, such as power and network
cables.
6. Route cable through cap and insert cap.
7. Close and lock cabinet compartment.
8. Commissioning
8.1. INFO POINT, COMPUTER DESK
 Connect monitor and computer to mains.
8.2. COMPUTER WORKSTATION
1. Plug monitor, computer, fan (and printer if applicable) into
socket strip or mains.
2. Size DE: Plug socket strip into mains.
9. Operation
9.1. INFO POINT, COMPUTER DESK, MOVING COMPUTER
WORKSTATION
CAUTION
Mobile computer workstation
Risk of crushing body.
» Make sure the paths for movement and transport are clear.
» No persons must be present in the direction of travel.
» Not for use in areas where the floor slopes upwards or down-
wards.
12
ü Device switched off and disconnected from the power supply.
Power cable stored in the cabinet.
ü Drawers and doors are closed and locked.
1. Release the parking brakes on both castors.
2. Move at walking pace.
3. Before starting work, apply the parking brakes on the castors.
9.2. USE FAN
i
Applies to article no. 948101 – 948805.
CAUTION
Rotating fan
Risk of minor or moderate injury to hands and fingers.
» When plugged into power supply, fan starts running immediately.
» Keep clear of fan when connecting to power supply.
» Only connect to a power supply circuit that can be shut down
with a master switch.
 The fan must be running whenever the computer is on.
10. Maintenance
Interval Action
Once a week in 1. Remove cover panel with a
rooms with nor-
mal levels of air
2. Clean filter.
pollution
3. Put cover panel back in
Once a day in
rooms with heavily
» Cover panel engages.
polluted air
Before the start of Check for external signs of
each shift damage, for defects and for
good condition. Check the
edges and guides for signs of
wear.
4. If defective, immediately
5. Have the damage repaired
Occasionally Grease any locks and wheels
with multi-function oil.
Tab. 1: Maintenance activities
11. Technical data
11.1. G DIMENSIONS
25 mm are equivalent to 1 G.
11.2. INFO POINT
Size
Weight
Overall load capacity
Load capacity of panel for keyboard
and mouse
Load capacity of the shelf
Load capacity of the monitor housing
Index of protection
Instruction manual
Performed by
Trained spe-
standard screwdriver. cialist for elec-
tro-technical
work
place.
Trained person
block access and prevent
use.
immediately.
Trained spe-
cialist for
mechanical
work
S/DE, S
63 kg
20 kg
5 kg
12 kg
4 kg
IP 41
M/DE, M
65 kg
20 kg
5 kg
12 kg
4 kg
IP 41