WMF Kult Pro Gebrauchsanweisung Seite 10

Initial operation Juicer
▪ Remove all packaging from the attachments.
▪ Clean the attachments before use as described in the "Cleaning and care" section.
▪ Place the transparent jug (9) inside the appliance to collect the pressed juice.
▪ Attach the strainer holder (14) to the spout (15) by twisting it slightly.
▪ Then insert the strainer holder (4) with the spout (15) into the motor unit.
▪ Insert the pressing cone (11,12) into the strainer (13), then insert the strainer (13) into motor unit
and twist clockwise to fix it tightly. The appliance cannot be operated if the strainer (13) is not
locked in place.
Note: The small pressing cone (12) is located within the large
pressing cone (11). If the small pressing cone (12) is to be
used, press down on the two opposing recesses and pull off
the large pressing cone (11).
If the large pressing cone (11) is to be used, it should be
attached to the small pressing cone (12). It clicks into place.
▪ Now insert the mains plug into the socket.
▪ To switch the appliance on, press the start/stop button.
▪ Press the cut surface of the halved citrus fruit into the pressing cone (12, 13).
▪ The pressed juice flows through the spout in the jug via the strainer (13) which retains the pulp and
pips.
Note: Clean the strainer (13) regularly to prevent it from overflowing.
▪ Switch the appliance off and then press the pressing cone (11,12) again for a few seconds at the
end so that the remaining juice can flow into the spout (15).
Useful tips
▪ Briefly reduce the pressure on the stopper (1,3) at regular intervals during the cutting to stop end-
less spirals from being created. This way the vegetable noodles will be shorter and easier to portion
out.
▪ Wherever possible you should fill the filler tubes (2,4) vertically to get the best results.
▪ The more level the outer surface of the food is, the easier the endless spirals are to cut. For that
reason, food such as carrots should be sliced before cooking.
▪ Food with a diameter of more than 60 mm cannot be processed, however they can be made into a
round shape by cutting off the sides and then processed.
▪ We recommend a maximum chopping time of 2 minutes.
Removing Juicer
▪ Switch the appliance off and pull out the mains plug.
▪ Take the transparent jug (9) containing the pressed juice out of the appliance and place it on the
side.
▪ Remove the strainer (13) by gently twisting it anti-clockwise.
▪ Remove the strainer holder (14) along with the spout (15) by gently pressing from below.
18
Cleaning and care Spiral cutter
Remove the mains plug after use. The motor unit (8) should never be placed in water, only wiped down
with a damp cloth. Never use abrasive cleaning agents. When cleaning the cutter inserts (5) and the
skewer support, be careful not to hurt yourself on the sharp blades and edges; Ideally, use the provided
washing-up brush (10), and you must always hold the cutter inserts (5) by the plastic parts. All
removable parts (stopper (1,3), collection container (9), filler tubes (2,4), cutter insert holders (6) and
cutter inserts (5)) can be placed in the dishwasher to make cleaning easier. However, we recommend
gently cleaning the cutter inserts (5) with warm running water and using a washing-up brush (10).
Regular washing in the dishwasher may blunt the blades.
Cleaning and care Juicer
Do not use harsh or abrasive cleaning agents.
Rinse all parts thoroughly in warm water.
Allow the parts to dry completely before reassembling them.
You can put the pressing cone (11,12), the strainer (13), the strainer holder (14), the spout (15) and the
jug (9) in the dishwasher for easy cleaning.
Important: Clean the strainer (13) and the spout (15) under warm water before placing in the dish-
washer by repeatedly pressing on the pump to rinse out the pulp residue.
19