Bauknecht BFP 5O41 PLT X Gebrauchsanweisung Seite 8

EN
SELECTING A CYCLE AND OPTIONS
The list of available cycles and options can be found in Cycle Table
on next page. Eco cycle is selected by default. If you want to have Last
Used cycle selected by default, you can change it in „Settings Menu".
It is possible to select a cycle by pressing 1 of 6 cycles direct access
buttons or by pressing „Extra Cycles"
last one is reached a further press goes back to the first.
Press cycle button to choose cycle in accordance with the level
of soiling of the dishes and with Cycle Table. Information will be
shown on the display:
1
1. Indicators
2. Name of the selected cycle
3. Vertical bar showing the position of the extra cycle list only
4. Energy consumption of the selected cycle
5. Water consumption of the selected cycle
50° 3:10
POWER
h
CLEAN
Press „INFO" button to display a brief description of the cycle and
its water / energy consumption.
NORMALLY SOILED CROCKERY.
STANDARD PROGRAM,
During the selection phase the „START/PAUSE"
Additional options are available for most cycles (see „Options and
Settings" section). When any option is selected, its name is shown on
the display on the right.
50° 3:10 POWER
h
CLEAN
When the cycle and option selection is complete, press „START/PAUSE"
button and close the door to start chosen cycle.
MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided
that it has only just begun: press and hold the „ON/OFF"
the machine will switch off.
Switch the machine back on using the „ON/OFF"
select the new wash cycle and any desired options; start the cycle by
pressing the „START/PAUSE"
TO PAUSE THE CYCLE (ADDING EXTRA ITEMS)
Open the door and place the crockery inside the dishwasher,
(beware of HOT steam!). Close the door and press „START/PAUSE"
button to resume the cycle from the point at which it was
interrupted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power
cut, the cycle stops. To resume the cycle from where it was interrup-
ted, close the door and press the „START/PAUSE"
8
button repeatedly. When the
2 3
ECO CYCLE
5 4
Three seconds after selecting a cycle, its
time and temperature will be displayed
(if available).
WATER ENERGY
LED blinks.
If more than one option is selected one
bullet point for each option is display-
ed. Each option name is displayed
for 3 sec. with its bullet point fulled.
button and
button.
button.
During the cycle, the progress is shown on the display (as bar) as well
as phase of cycle, and time to the end of the cycle with ":" blinking:
Depending at the selected cycle, the display may provide additional
information:
• - sensor is adjusting time and energy and water con-
SENSOR
sumption to the level of soil amount on the dishes. Present only in
AUTO SENSOR cycle.
• - extra items can be added.
PRE-WASH
• - main washing.
WASHING
• - drying phase of cycle.
DRYING
After the cycle finishes, there is an acustic signal and the dispaly
shows:
On the display additional information can be shown:
• ADD SALT - refill salt reservoir.
• ADD RINSE AID - refill rinse aid.
• DEGREASE AND CLEAN MACHINE WE RECOMMEND WPRO - every 50
cycle, will be recommended to use the WPRO cleaner (according to
instruction on the consumable).
Open appliance door (beware of hot steam!) and unload the racks,
starting from the lower rack first.
If it is needed to refill salt reservoir or rinse aid dispenser, it is
recommended to do this operations right before start of the next
cycle.
After 10 minutes the appliance switches off.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently
preventing scale buildup on heater, contributing also to better cleaning
efficiency.
This system regenerates itself with salt, therefore it is required to
refill salt container when empty.
Frequency of regeneration depends on water hardness level setting -
regeneration takes place once per 6 Eco cycles with water hardness
level set to 3.
Regeneration process starts in final rinse and finishes in drying phase,
before cycle ends.
• Single regeneration consumes: ~3.5L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
button,
WASHING
1:20h
CYCLE FINISHED