Settings Menu - Bauknecht BFP 5O41 PLT X Gebrauchsanweisung

SETTINGS MENU

To change machne settings you need to enter into the Settins Menu.
Press „OK" button and navigate with „< , >" until
To exit the setting menu, press any cycle button or press „< , >" button untill
Language
1.LANGUAGE
1.ITALIANO < >
1.ENGLISH
First cycle
2.FIRST CYCLE
2.<ECO> < >
2.<LAST USED>
Sounds
3.SOUNDS
3.<HIGHT> < >
3.<OFF>
Water Hardness
4.WATER HARDNESS
4.WATER HARDNESS
To setup correct level according to water hardness, see table on page 4.
Screen Brightness
5.SCREEN BRIGHT.
5.SCREEN BRIGHT.
Choose between five levels: 1, 2, 3, 4 and 5.
Tub Light
6.TUB LIGHT
6.TUB LIGHT OFF
SETTINGS
To change language, enter in the
OK
setting menu by pressing „OK"
button and navigate with „< , >"
until „LANGUAGE" is shown, then
press „OK" button.
You can choose which cycle is
OK
selected by default when switching
on the appliance: ECO or the LAST
USED one.
To change first cycle, enter in the
setting menu by pressing „OK" but-
ton and navigate with „< , >" until
„FIRST CYCLE" is shown, then press
„OK" button.
To change sounds, enter in the
OK
setting menu by pressing „OK"
button and navigate with „< , >"
until „SOUNDS" is shown, then press
„OK" button.
Choose between 2 levels: High;
Low. Can be also OFF.
To change water hardness level,
3
enter in the setting menu by
pressing „OK" button and navigate
4
with „< , >" until „WATER HARDNESS"
is shown, then press „OK" button.
To change screen brightness
5
level, enter in the setting menu by
pressing „OK" button and navigate
3
with „< , >" until „SCREEN BRIGHT. " is
shown, then press „OK" button.
To change tub light, enter in the
ON
setting menu by pressing „OK"
button and navigate with „< , >"
until „TUB LIGHT" is shown, then
press „OK" button.
is shown, then press „OK" button.
is shown, then press „OK" button.
EXIT
ActiveDry
ActiveDry is a convection drying system which automatically opens
the door during/after drying phase to ensure exceptional drying
performance every day. Door opens at the temperature that is safe to
your kitchen furniture, thus door will not be opened when the option
of TURBO is on.
As additional steam protection, special designed protection foil is added
together with the dishwasher (depending on the model type - can be
the need to buy it). To see how to mount protection foil please refer to
(INSTALLATION GUIDE).
ActiveDry functionality could be disabled by the user as follows:
7.ACTIVEDRY
7.ACTIVEDRY
Rinse Aid level
8.RINSE AID LEV.
8.RINSE AID LEV.
Choose between five levels: 1, 2, 3, 4 and 5.
If the rinse aid level is set to 1, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
The factory setting is for (5) level .
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set
a high number (4-5).
Demo mode
9.DEMO MODE
9.DEMO MODE
Reset to factory default
10.RESET TO DEF.
10.ON
10.OFF
Exit
11.EXIT
To set ActiveDry on or off, enter in
ON
the setting menu by pressing „OK"
button and navigate with „< , >"
OFF
until „ActiveDry" is shown, then
press „OK" button.
To change rinse aid level, enter in
5
the setting menu by pressing „OK"
button and navigate with „< , >"
until „RINSE AID LEV. " is shown, then
4
press „OK" button.
To see the demo mode, enter in the
SET
setting menu by pressing „OK"
button and navigate with „< , >"
OFF
until „DEMO MODE" is shown, then
press „OK" button.
To reset to factory default, enter in
OK
the setting menu by pressing „OK"
button and navigate with „< , >"
< >
until „RESET TO DEF. " is shown, then
press „OK" button.
To exit the setting menu, press any
< >
cycle button or press „< , >" button
untill is shown, then press
EXIT
„OK" button.
EN
11