Options And Settings; Multi-Zone - Bauknecht BFP 5O41 PLT X Gebrauchsanweisung

EN

OPTIONS AND SETTINGS

With each cycle additional options can be used. A full list of available options working with specific cycles can be found in the Cycle Table on
the previous page. All active options are shown on the display.
To set an option press „OK" button.
option list. Press „OK" to select the option, in the setting menu the LED above „OK" button is lit.
If the option is not available, it will be still visible in its position but with „
TABLET (All-in-one)
This setting allows you to optimise the performance of the cycle
according to the type of detergent used. Enable it if you use combined
detergents in tablet form (rinse aid, salt and detergent in 1 dose).
TABLET OFF
TABLET ON
TABLET ON
START DELAY
The start of the cycle may be delayed for a selected period of time.
To set a delay, enter in the setting menu by pressing „OK" button and na-
vigate with „< , >" until „START DELAY" is shown, then press „OK" button.
With each press of the button ">" or "<", the delay start increases by:
• every 0:30 if selection below 4 hours,
• every 1:00 if selection is below 12 hours,
• every 2 hours if selection is above 12 hours.
START DELAY OFF
<STARTS IN h> OFF
<STARTS IN h> 4:00
<STARTS IN h> 4:00
To remove the delay, press „<" or „>" button until „OFF" is displayed.
MULTIZONE
If there are not many dishes to be washed it can be loaded in one rack
only. Using this option you can select which rack you want to wash.
Select a compatible cycle (see "Cycles table"), and then press the
MULTIZONE button: the symbol of the chosen rack will appear on
the display.
By default the MULTIZONE is not active and all racks icons are lit.
Selected only lower rack
Selected only upper rack
Selected only cutlery rack
Remember to load the upper or lower rack only, and to reduce
the amount of detergent accordingly.
If upper rack is removed, please apply detergent directly
to the tub instead of detergent dispenser.
10
SET OPTIONS message is shown for a few seconds. Then use „<" or „>" button to navigate through the
To set the Tablet, enter in the setting
menu by pressing „OK" button and
navigate with „< , >" until „TABLET"
is shown, then press „OK" button.
Default value is OFF.
If delay is selected, the is
Once „OK" button is pressed the
delay is confirmed and the machine
comes back to the cycle selection
screen with delay value visible.
Press „START/PAUSE" button to
start the delay.
"
POWER CLEAN
Thanks to additional water jets this option provides a more intensive
and powerful wash in the specific area of lower rack.
POWER CLEAN
POWER CLEAN
POWER CLEAN
TURBO
This option can be used to reduce the duration of the main cycles
while maintaining washing and drying performance levels.
TURBO
TURBO
TURBO
. lit.
KEYLOCK
KEYLOCK ACTIVATED
PRESS "OK" FOR 3 SEC.
KEEP PRESSED...
KEYLOCK DEACTIVATED
Once set, to deactivate it keep pressing „OK" button for a few seconds.
TUB LIGHT
When the feature is active the LEDs in the tub are automatically
switched on/off as soon as the user open/close the door respectively.
If the door remains opened for more than 10 min, the LEDs in the
tub switch off (to turn them on again, the door has to be closed and
opened again).
This feature is active by default, but it is possible to deactivate it in the
"SETTINGS MENU".
Default value is OFF.
OFF
To set the Power Clean, enter in
the setting menu by pressing „OK
ON
button and navigate with „< , >"
until „POWER CLEAN" is shown,
ON
then press „OK" button.
To set the Turbo, enter in the setting
OFF
menu by pressing „OK" button and
navigate with „< , >" until „TURBO"
ON
is shown, then press „OK" button.
With each press of the button
ON
„>" or „<" option will be ON or OFF.
Confirm by pressing „OK" button.
The KEYLOCK function blocks the
control panel except the „ON/OFF"
button.
To activate the Keylock, enter in the
setting menu by pressing „OK" button
and navigate with „< , >" until
„KEYLOCK" is shown, then press OK.