First Time Use - Bauknecht BFP 5O41 PLT X Gebrauchsanweisung

EN

FIRST TIME USE

After connecting the appliance to the power supply for the first time,
the display will guide you to set up the appliance for first use.
1. The language selection
LANGUAGE: ENGLISH?
<> = CHANGE OK = YES
ENGLISH
SELECTED
After language confirmation, the appliance will go through the first time
use configuration menu.
2. Setting the water hardness
WATER HARDNESS
(1=MIN, 5=MAX)
WATER HARDNESS = 3
<> = CHANGE OK = YES
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
Water Hardness Table
°dH
Level
German degrees
1 Soft 0 - 6
2 Medium 7 - 11
3 Average 12 - 16
4 Hard 17 - 34
5 Very hard 35 - 50
3. Filling the water softener
POUR WATER
OPERATION
INSERT 1,5 LITER OF
OK = DONE
WATER IN THE
OK = DONE
WATER SOFTENER
OK = DONE
INSERT SALT
OPERATION
ADD 1KG OF SALT
OK = DONE
IN THE SALT DISPENSER
OK = DONE
Position the funnel (see figure) and fill the salt reservoir right up to its
edge (approximately 1 kg); it is not unusual for some water will spill out.
Remove the funnel and wipe any salt residue away from the opening.
4
To select preferred language please
press button „<" or „>".
Confirm by pressing „OK" button.
The water hardness is by default
set to level 3. To change water
hardness level press button „<" or „>"
repeatedly.
To confirm your choice press „OK"
button. The level must be set
according to the table below.
°fH °Clark
French degrees English degrees
0 - 10 0 - 7
11 - 20 8 - 14
21 - 29 15 - 20
30 - 60 21 - 42
61 - 90 43 - 62
When water hardness is set, it is
required to fill water softener with
water and special regeneration salt.
Remove the lower rack and unscrew
the reservoir cap (anticlockwise)
As a first step it is needed to fill
reservoir with water ( ~1.5 litres).
Once done, proceed to the next
step by pressing „OK" button.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Once done, proceed to the next step by pressing „OK" button.
Only use salt that has been specifically designed for dishwashers.
Whenever you need to add salt, it is mandatory to complete the pro-
cedure before the beginning of the washing cycle to avoid corrosion.
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher detergent.
4. Setting the brightness level
ADJUST BRIGHTNESS
(1=MIN, 5=MAX)
BRIGHTNESS = 5
<> = CHANGE OK = YES
5. Detergent type operation
DETERGENT TYPE
OPERATION
DO YOU USE
<> = NO OK = YES
"ALL IN ONE"
<> = NO OK = YES
DETERGENT?
<> = NO OK = YES
The symbol on display will be lit. If you prefer to use gel or
powder detergent for washing, press „<" or „>", then go to step 6.
Rinse aid operation.
6. Rinse aid operation*
*If All-in-one detergent was chosen in the previous step, this step will
be skipped by the appliance.
RINSE AID
OPERATION
INSERT RINSE AID
OK = DONE
IN THE DISPENSER
OK = DONE
B
The brightness level is by default set
to level 5. To change brightness level
press button „<" or „>" repeatedly.
To confirm Your choice press „OK"
button.
In this step it is very important to
choose what type of detergent will
be used (tablet/capsule or
gel/powder).
If you prefer to use All-in-one
detergent in tablet or capsule for
washing - press „OK", then go to
step 7. Open tap operation on the
next page.
A