Renkforce 754171 Bedienungsanleitung Seite 2

G Operating instructions
LED Strobe Light
Item no. 754171 (red)
Item no. 754173 (orange)
Intended Use
When connected to the operating voltage (12 -24 V/DC), the LED strobe light will gen-
erate regular short flashes of light (flash rate of 7.62 Hz and 24.75 Hz depending on the
connection). Due to this feature the LED flash light can be used e.g. for signalling in
alarm systems, generating light effects or the indication of operating conditions.
The product may be installed and used outdoors and indoors (IP65).
Any use other than that described above could lead to damage to this product and
involves the risk of short circuits, fire, electric shock, etc. No part of the product may
be modified or converted!
The safety instructions must be observed at all times!
This product complies with the applicable national and European requirements. All
names of companies and products are the trademarks of the respective owners. All
rights reserved.
Package Contents
• LED Strobe Light
• 2x stickers "Fire"
• 2x stickers "Alarm"
• Operating instructions
Explanation of Symbols
This symbol indicates specific risks associated with handling, function and
use.
The "arrow" symbol indicates special tips and operating information.
Safety Instructions
R ead carefully the complete operating manual before starting to use it. It
contains important information about correct operation.
D amage due to not following these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
W e do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions! In such
cases, the warranty will be null and void.
• Unauthorised conversion and/or modification of the product is not al-
lowed for safety and approval reasons (CE).
• The product must not be exposed to extreme temperatures, strong vibra-
tions or heavy mechanical stress.
• The product is not a toy and should be kept out of the reach of children!
• Do not use the product in rooms with adverse environmental conditions,
where combustible gases, vapours or dust are or may be present! There
is a risk of explosion!
• Caution, LED light: Do not look directly into the LED light! Do not look into
the beam directly or with optical instruments! Danger of damage to eyes!
• Regular flashing of the light source may trigger epileptic seizures in cer-
tain people. This may also happen to people who have never before expe-
rienced an epileptic seizure.
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Em-
ployer's Liability Insurance Association for Electrical Systems and Operat-
ing Facilities are to be observed!
• If you have any questions that are not answered in these operating in-
structions, please contact our technical department or another specialist.
Assembly
• The LED strobe light can generate flashes of light at two different flash rates; de-
pending on the connection, the flash frequency is 7.62 Hz or 24.75 Hz:
Flash frequency 7.62 Hz
Black wire GND/negative terminal (-)
Red wire positive terminal (+):
Flash frequency 24.75 Hz
Black wire GND/negative terminal (-)
Yellow wire positive terminal (+): 12 - 24 V/DC
If only need one flash rate is required, insulate the unused wire e.g. with
shrink tubing.
Depending on the desired function, it is possible to switch between the flash
rates (e.g., using an external switch, etc.).
• Depending on the surface, the LED strobe light must be secured with two suitable
screws, and wall plugs if necessary. However, before this, a large enough opening
for the connecting cable is needed.
Protect the connecting cables from short-circuit. When installing the product out-
doors, make sure that moisture cannot penetrate the cable connections (e.g. screw
connections, terminals).
Take care not to damage any existing electrical wiring, gas or water pipes,
when you are drilling holes or the tightening screws.
• Switch on the mains voltage and check that the LED strobe light is working.
Maintenance and Care
• The product does not require maintenance. The LED bulb is permanently installed
and cannot be replaced.
• Only the outer surface of the LED strobe light should be wiped using a clean, soft,
dry cloth. Do not use aggressive cleaning agents or chemical solutions that could
damage the housing (discolouring) or impair operation.
Do not press too hard on the housing, as scratches might appear.
Dust can easily be removed using a clean, soft brush and a vacuum cleaner.
Disposal
Please dispose of the product at the end of its life cycle according to the
applicable statutory requirements.
Technical Information
Operating voltage............................... 12 - 24 V/DC
Power consumption........................... max. 120 mA
Lamp ..................................................... LED, not replaceable
Protection class
.......................................
Flash frequency .................................. 7.62 Hz or 24.75 Hz (depending on connection)
Cable length
. ..............................................
Dimensions.......................................... 38 x 110 x 35 mm (L x W x H)
Weight .................................................. 53 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.
12 - 24 V/DC
IP65
approx. 160 mm