Herunterladen Diese Seite drucken

Fehlerbeseitigung - TFA 31.1134 Bedienungsanleitung

Scantemp 330
Vorschau ausblenden Andere Handbücher für 31.1134:

Werbung

TFA_No. 31.1134_Anleitung
ScanTemp 330 - Infrarot-Thermometer

8. Fehlerbeseitigung

Problem
Lösung
➜ Gerät anschalten - Mess-Taste drücken
Keine Anzeige
➜ Batterie polrichtig einlegen
➜ Batterie wechseln
➜ Gemessene Temperatur liegt außerhalb des
Anzeige „HI/LO"
9. Entsorgung
Batterien und Akkus dürfen keinesfalls in den Hausmüll!
Als Verbraucher sind Sie gesetzlich verpflichtet, gebrauchte Batterien und Akkus
zur umweltgerechten Entsorgung beim Handel oder entsprechenden Sammel-
stellen gemäß nationaler oder lokaler Bestimmungen abzugeben.
Die Bezeichnungen für enthaltene Schwermetalle sind: Pb=Blei
Dieses Gerät ist entsprechend der EU-Richtlinie über die Entsorgung von Elek-
tro- und Elektronik-Altgeräten (WEEE) gekennzeichnet.
Dieses Produkt darf nicht mit dem Hausmüll entsorgt werden. Der Nutzer ist
verpflichtet, das Altgerät zur umweltgerechten Entsorgung bei einer ausgewie-
senen Annahmestelle für die Entsorgung von Elektro- und Elektronikgeräten
abzugeben.
10. Technische Daten
Temperaturmessbereich:
-50 °C ...+ 330 °C / -58 °F...+626 °F
Arbeitsbereich:
0 °C ...+ 50 °C / +32 °F...+122 °F
Genauigkeit:
-50°C...0°C / -58°F...+32°F: ±4 °C / 9 °F
0°C...+ 330°C / +32...+626 °F: ±2 °C / 4 °F
Laser:
Output < 1 mW, 630....670 nm
Emissionsgrad:
0,95 fest
Auflösung:
0,1°C / 0,1 °F
Ansprechzeit (90%):
< 1 Sekunde
Messfleck-Verhältnis:
12 : 1
Spannungsversorgung:
9 Volt Batterie
Automatische
Abschaltfunktion:
ca. 10 Sekunden
Gehäusemaße:
32 x 78 x 133 mm
Gewicht:
97 g (nur das Gerät)
TFA Dostmann GmbH & Co.KG, Zum Ottersberg 12, D-97877 Wertheim.
Diese Anleitung oder Auszüge daraus dürfen nur mit Zustimmung von TFA Dostmann ver-
öffentlicht werden. Die technischen Daten entsprechen dem Stand bei Drucklegung und können
ohne vorherige Benachrichtigung geändert werden.
www.tfa-dostmann.de
4
05.12.2013
13:52 Uhr
Seite 3
Messbereichs
ScanTemp 330 - Infrared Thermometer
1. Before you start using it
• Please make sure to read the instruction manual carefully.
• Following and respecting the instructions in your manual will prevent damage to your
instrument and loss of your statutory rights arising from defects due to incorrect use.
• We shall not be liable for any damage occurring as a result of non-following of these
instructions. Likewise, we take no responsibility for any incorrect readings and for any
consequences which may result from them.
• Please take particular note of the safety advice!
• Please keep this instruction manual for future reference.
2. Field of operation and all the benefits of your new instrument at a glance
• For contact-free measuring of surface temperature even of hot, hazardous, or hard-to-reach
objects.
3. For your safety
• This product is exclusively intended for the field of application described above. It should
only be used as described within these instructions.
• Unauthorized repairs, modifications or changes to the product are prohibited.
• This product is not be used for medical purpose or for public information, it is only intended
for home use. The product is not recommended for taking body temperature.
Do not look directly into the laser beam – permanent eye damage may
Caution!
Risk of injury:
• Do not aim too close at hot or dangerous targets.
• Keep this instrument and the battery out of the reach of children.
• Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk of
explosion!
• Batteries contain harmful acids. Low batteries should be changed as soon as possible to
prevent damage caused by leaking.
• Wear chemical-resistant protective gloves and safety glasses when handling leaking batter-
ies.
Important information on product safety!
• Do not place your product near extreme temperatures, vibrations or shocks.
• Protect the unit from large or abrupt ambient temperature changes.
• Do not leave the unit near objects of high temperature.
• Do not immerse the unit in water. Water can penetrate and cause malfunction. Protect it
from moisture.
• Steam, dust, smoke, etc., can prevent accurate measurement by obstructing the unit's
12/2013
optics.
CAUTION - LASER CLASS II
result.
5

Werbung

loading