Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
10 MHz Function Generator HM8130
Valid at 23 degrees °C after a 30 minute warm-up period
Frequency
Range:
10 mHz to 10 MHz
Resolution:
5-digit, max. 10 mHz
Display:
5-digit LED
Accuracy:
± (1 digit + 5 mHz)
Temperature coefficient:
0.5 ppm/° C
Aging:
2 ppm/year
Waveforms
Sine wave
Frequency range:
10 mHz to 10 MHz
Amplitude:
0 - 20 V
Distortion:
to 500 kHz:
500 kHz-3 MHz: ‹ 1 %
3 MHz-10 MHz:
Square wave
Frequency range:
10 mHz to 10 MHz
Amplitude:
0 - 20 V
Rise/fall time:
‹ 10 ns
Overshoot:
‹ 5 % (V
Symmetry:
50 % ± (5 % +10 ns)
Pulse
Frequency range:
10 mHz to 5 MHz
Amplitude:
0...+10 V and 0...-10 V
Rise/fall time:
‹ 10 ns
Pulse width:
100 ns to 80 s
Duty cycle:
max. 80 %
Saw thooth
Frequency range:
10 mHz to 500 kHz
Amplitude:
0 - 20 V
Linearity:
better than 1 %
Triangle
Frequency range:
10 mHz to 2 MHz
Amplitude:
0 - 20 V
Linearity:
better than 1 %
Arbitrary generator
Frequency range:
10 mHz to 100 kHz
Amplitude:
max. 20 V
Sampling rate:
40 MSa/s
Resolution:
X: 1024 (10 bit); Y: 4096 (12 bit)
Inputs
Gate/trigger:
BNC connector
Impedance:
5 kΩ II 100 pF; protected up to ± 30 V
AM-IN:
amplitude modulation, BNC connector
Impedance:
10 kΩ; protected up to ± 30 V
Outputs
Signal output:
(BNC connector)
short-circuit proof; ext. voltage max. ± 15 V
Impedance:
50 Ω
Output voltage:
Range 1:
Range 2:
Range 3:
Resolution:
Range 1:
Range 2:
Range 3:
Setting accuracy:
Range 1:
(1kHz)
Range 2:
Range 3:
3 % additional for pulse and square wave
Frequency response:
‹ 100 kHz:
100 kHz - 2 MHz: ± 0.5 dB
2 MHz - 10 MHz: + 0.5 dB / - 3 dB
Offset error:
± 50 mV (Range 3)
Display:
2
1
/
w w w . h a m e g . c o m
HM8130E/0405/ce · Subject to alterations · © HAMEG GmbH · ® Registered Trademark · DQS-certified in accordance with DIN EN ISO 9001:2000, Reg.-No.: DE-071040 QM
HAMEG GmbH
Industriestr. 6
·
(open circuit)
pp
‹ 0.5 %
‹ 3 %
(open circuit)
pp
≥ 200 mV)
out
(open circuit)
pp
(open circuit)
pp
(open circuit)
pp
2.1 - 20 V
(open circuit)
pp
0.21 - 2.0 V
(open circuit)
pp
20 - 200 mV
(open circuit)
pp
100 mV
10 mV
1 mV
± 2 %
± 3 %
± 4 %
± 0.2 dB
digit (LED)
2
D-63533 Mainhausen
Tel +49 (0) 6182 800 0
·
·
DC offset
Output voltage:
Range 1:
Range 2:
Range 3:
Trigger output (BNC connector)
Ramp:
0 to 5 V (sweep out)
Level:
5 V/TTL
Output impedance:
1 kΩ
Internal sweep
Selectable start and stop frequency
Internal sweep:
all waveforms
Sweep time:
linear from 20 ms to 100 s,
continuous or triggered
(ext. signal, interface)
Amplitude modulation:
Modulation via external signal
Modulation depth:
0 to 100 %
Bandwidth:
DC - 20 kHz (-3 dB)
Gate (asynchronous)
Modulation on/off via external TTL signal
Delay time:
‹ 150 ns
Input signal:
TTL
Trigger function (synchronous)
Burst mode via ext. trigger input or interface
Frequency range:
‹ 500 kHz
Miscellaneous
Memory: For the last device settings and for 8 arbitrary signals
Safety class:
Safety Class I (EN61010-1)
Power supply:
115/230 V ± 10 %; 50/60 Hz
Power consumption:
approx. 20 Watt
Operating temperature:
+10° C to + 40° C
Max. relative humidity:
10 % -90 % (without condensation)
Dimensions (W x H x D):
285 x 75 x 365 mm
Weight:
approx. 5 kg
Accessories supplied: Operator's Manual, power cable, software-CD
Optional accessories: HZ10 Silicone test leads, HZ33/HZ34 50 Ω Test Cable,
BNC-BNC, HZ24 Set of attenuators, 3/6/10 and 20 dB, HZ42 19" Rackmount kit
2RU, HZ20 Adapter Plug
Fax +49 (0) 6182 800 100
·
-7.5...+ 7.5 V (open circuit)
-0.75...+ 0.75 V (open circuit)
-75...+ 75 mV (open circuit)
www.hameg.com
info@hameg.com
·
·
Werbung
Kapitel
Inhaltsverzeichnis
