Zumtobel SensControl II Bedienungsanleitung Seite 9

SensControl II Lighting management
Functions of SensControl II Operating SensControl II
Tip
The set value for
illuminance can be
modified and the
constant lighting
control can be
activated/deactivated
via the operating
Operation
keys.
Switch on luminaire
Switch off luminaire
Tip
The delay time can be
Manually adjust illuminance
adjusted or presence
(dimming)
detection deactivated
via the operating
keys.
Tip
The lockout function
can be activated/
deactivated and
switching between
Parameters and factory settings
fully automatic and
semi-automatic
control can be
implemented via the
Tip
Unplug the power
operating keys.
supply and connect
again while pressing
the key to reset the
factory settings.
Installing the luminaire
a LED flashes once to
confirm.
Tip
In order to ensure
optional functionality
of the system, it must
be ensured that
sensors are aligned
towards the working
area during luminaire
installation.
Modifying settings
2 EN
Mat.-Nr. 00104565/5/P- 05.10
Mat.-Nr. 00104565/5/PA 11.11
SensControl II Lighting management
Lighting management
The functions of SensControl II ensure a high level of convenience at the workstation Operation of SensControl II is via keys on the luminaire. The functions of the keys
and can significantly reduce energy consumption. differ according to appearance:
Constant lighting control
The constant lighting control function of SensControl II adapts the lighting
automatically to the lighting conditions at the workstation (sunshine, overcast sky,
closed blinds). A brightness sensor compares the illuminance on the working plane
with an adjustable set value for this purpose. If illuminance is not sufficient, the
lacking light quantity is adjusted upwards. If there is too much light, the luminaire is
Single-channel version
adjusted downwards. Adjustment is carried out with a certain rate of inertia in order
without separation of
to prevent a rapid and therefore unpleasant modification of illuminance.
indirect/direct light
Presence detection
p Press lower/upper key. p Briefly press upper key. p Briefly press lower key.
p Press lower key.
The luminaire is automatically switched on or off via presence detection. A passive
infrared sensor (PIR) monitors the detection range for this purpose. The luminaire is
p Press and hold upper
automatically switched on as soon as someone enters the detection range. If however
key until the desired
the constant lighting control registers an illuminance level above the individually
illuminance level is set.
adjusted set value, the luminaire remains in stand-by operation. The luminaire
automatically switches to stand-by operation if nobody is registered in the detection
range within an adjustable delay time.
Lockout and automatic function
a LED flashes rapidly until max. or min. value is reached.
p Release the key and press and hold again to alternate the direction of adjustment.
Use of the luminaire at switchable sockets can be optimised with the lockout. If the
The set value for constant lighting control is automatically restored following a
lockout is activated and following a mains disconnection, the luminaire remains in
longer period of absence (at least 4 hours) or following a mains disconnection.
stand-by until presence is detected or until it is manually switched on. If lockout is
deactivated, the luminaire automatically switches on again following mains
disconnection.
SensControl II enables fully automatic operation of luminaires at workstations
without intervention of users being necessary. With activated semi-automatic The following parameters are available for individual adjustment of functions:
operation the luminaire is automatically switched off with absence, but switching on
Parameter
of the luminaire must occur manually. This enables maximum energy savings.
Unintentional automatic switching on (e.g. in areas near to corridors) is avoided in this
Constant lighting control
way.
Set value for constant
lighting control
Delay time
Control
Lockout
Tip
If you do not press a key within a twenty second period during adjustment of
constant lighting control, presence detection, lockout or automatic control,
SensControl II switches back to operating mode and the modifications are not
saved. If you have pressed keys erroneously, wait 20 seconds and repeat the
adjustment.
Dual-channel version
with separate indirect/direct light
Indirect lighting
p Press and hold upper
key until the desired
illuminance level is set.
During dimming take care that you do not press both
keys simultaneously, as in this case SensControl II
switches to setting mode.
Adjustable values
activated/deactivated
5 - 100 %
10 seconds (demo mode),
1, 5, 15, 30 minutes,
Presence detection deactivated
semi-automatic/ fully
automatic
activated/deactivated
Direct lighting
p Press and hold lower
key until the desired
illuminance level is set.
Factory setting
activated
15 minutes
fully automatic
activated
2 EN 1 EN
www.zumtobel.com