Stand-By Operation - Zumtobel SensControl II Bedienungsanleitung

SensControl II Lighting management
Functions of SensControl II Setting lockout and automatic control
Tip
The set value for
illuminance can be
modified and the
constant lighting
control can be
activated/deactivated
via the operating
keys.
Tip
The delay time can be
adjusted or presence
detection deactivated
via the operating
keys.
Tip
The lockout function
can be activated/

Stand-by operation

deactivated and
switching between
fully automatic and
semi-automatic
control can be
implemented via the
Questions about SensControl II
operating keys.
Installing the luminaire
Tip
In order to ensure
optional functionality
of the system, it must
be ensured that
sensors are aligned
towards the working
area during luminaire
installation.
4 EN
Mat.-Nr. 00104565/5/P- 05.10
Mat.-Nr. 00104565/5/PA 11.11
SensControl II Lighting management
Lighting management
The functions of SensControl II ensure a high level of convenience at the workstation
Activating/deactivating lockout
and can significantly reduce energy consumption.
1. Press both keys simultaneously and hold for 8 seconds.
a LED lights up.
Constant lighting control
2. Briefly release both keys and press again simultaneously, holding for 5 seconds.
a LED flashes slowly.
The constant lighting control function of SensControl II adapts the lighting
3. Press upper key 5 times to deactivate the lockout.
automatically to the lighting conditions at the workstation (sunshine, overcast sky,
- or -
closed blinds). A brightness sensor compares the illuminance on the working plane
Press upper key 6 times to activate the lockout.
with an adjustable set value for this purpose. If illuminance is not sufficient, the
a LED flashes 5 or 6 times to confirm.
lacking light quantity is adjusted upwards. If there is too much light, the luminaire is
4. adjusted downwards. Adjustment is carried out with a certain rate of inertia in order Press both keys simultaneously and hold for 8 seconds to permanently save the
to prevent a rapid and therefore unpleasant modification of illuminance. setting.
a The LED extinguishes.
Presence detection
Switching between fully automatic and semi-automatic control
Press both keys simultaneously and hold for 8 seconds.
1. The luminaire is automatically switched on or off via presence detection. A passive
infrared sensor (PIR) monitors the detection range for this purpose. The luminaire is a LED lights up.
automatically switched on as soon as someone enters the detection range. If however
2. Briefly release both keys and press again simultaneously, holding for 5 seconds.
the constant lighting control registers an illuminance level above the individually
a LED flashes slowly.
adjusted set value, the luminaire remains in stand-by operation. The luminaire
3. Press upper key 1 time to activate semi-automatic control.
automatically switches to stand-by operation if nobody is registered in the detection
- or -
range within an adjustable delay time.
Press upper key 2 times to activate fully automatic control.
a LED flashes 1 or 2 times to confirm.
Lockout and automatic function
4. Press both keys simultaneously and hold for 8 seconds to permanently save the
setting.
Use of the luminaire at switchable sockets can be optimised with the lockout. If the
a The LED extinguishes.
lockout is activated and following a mains disconnection, the luminaire remains in
stand-by until presence is detected or until it is manually switched on. If lockout is
deactivated, the luminaire automatically switches on again following mains
disconnection.
The LED lights up in stand-by operation to indicate the functional integrity of the
SensControl II enables fully automatic operation of luminaires at workstations
luminaire. Power consumption in stand-by operation is < 0.2 W.
without intervention of users being necessary. With activated semi-automatic
operation the luminaire is automatically switched off with absence, but switching on
of the luminaire must occur manually. This enables maximum energy savings.
Unintentional automatic switching on (e.g. in areas near to corridors) is avoided in this
way.
If you have any questions about SensControl II please contact:
Zumtobel Lighting GmbH
Achtzehn-Morgen-Weg 2-4
61250 Usingen
Germany
Tel.: +49 (0) 6081 1026-110
You can find general information about our products on our website at
www.zumtobel.com or from our sales partners responsible. If you have specific
questions, please contact your sales partner.
1 EN 4 EN
www.zumtobel.com