Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SensControl II Lighting management
Setting constant lighting control
Operating SensControl II
Operating SensControl II
Operation
Operation
Switch on luminaire
Switch on luminaire
Switch off luminaire
Switch off luminaire
Manually adjust illuminance
Manually adjust illuminance
(dimming)
(dimming)
Parameters and factory settings
Parameters and factory settings
Tip
Tip
Setting presence detection
Unplug the power
Unplug the power
supply and connect
supply and connect
again while pressing
again while pressing
the key to reset the
the key to reset the
factory settings.
factory settings.
a LED flashes once to
a LED flashes once to
confirm.
confirm.
Modifying settings
Modifying settings
3 EN
2 EN
2 EN
Mat.-Nr. 00104565/5/P- 05.10
SensControl II Lighting management
SensControl II Lighting management
Tip
Operation of SensControl II is via keys on the luminaire. The functions of the keys
Operation of SensControl II is via keys on the luminaire. The functions of the keys
Stand next to the luminaire when setting the constant lighting control and make
differ according to appearance:
differ according to appearance:
sure that the sensor is not blocked.
Modifying the set value for constant lighting control
1.
Press both keys simultaneously and hold for 8 seconds.
a The LED lights up.
2.
With single-channel version:
Press and hold upper key until the desired illuminance level is set.
a LED flashes rapidly until max. or min. value is reached.
Single-channel version
Single-channel version
3.
With dual-channel version:
without separation of
without separation of
Press and hold upper key until the desired illuminance level is set for indirect light.
indirect/direct light
indirect/direct light
Press and hold lower key until the desired illuminance level is set for direct light.
a LED flashes rapidly until max. or min. value is reached.
p Press lower/upper key. p Briefly press upper key. p Briefly press lower key.
p Press lower/upper key. p Briefly press upper key. p Briefly press lower key.
4.
Release the key and press and hold again to alternate the direction of adjustment.
p Press lower key.
p Press lower key.
Press both keys simultaneously and hold for 8 seconds to permanently save the
5.
p Press and hold upper
p Press and hold upper
setting.
key until the desired
key until the desired
a The LED extinguishes.
illuminance level is set.
illuminance level is set.
Activating/deactivating constant lighting control
1.
Press both keys simultaneously and hold for 8 seconds.
a LED lights up.
2.
Briefly release both keys and press again simultaneously, holding for 5 seconds.
a LED flashes rapidly until max. or min. value is reached.
a LED flashes rapidly until max. or min. value is reached.
a LED flashes slowly.
p Release the key and press and hold again to alternate the direction of adjustment.
p Release the key and press and hold again to alternate the direction of adjustment.
3.
Press upper key 3 times to deactivate the constant lighting control.
The set value for constant lighting control is automatically restored following a
The set value for constant lighting control is automatically restored following a
- or -
longer period of absence (at least 4 hours) or following a mains disconnection.
longer period of absence (at least 4 hours) or following a mains disconnection.
Press upper key 4 times to activate the constant lighting control.
a LED flashes 3 or 4 times to confirm.
4.
Press both keys simultaneously and hold for 8 seconds to permanently save the
setting.
a The LED extinguishes.
The following parameters are available for individual adjustment of functions:
The following parameters are available for individual adjustment of functions:
Parameter
Parameter
Constant lighting control
Constant lighting control
Modifying delay time or deactivating presence detection
Set value for constant
Set value for constant
1.
Press both keys simultaneously and hold for 8 seconds.
lighting control
lighting control
a LED lights up.
Delay time
Delay time
2.
Briefly release both keys and press again simultaneously, holding for 5 seconds.
a LED flashes slowly.
3.
To set the delay time with the lower key:
Control
Control
•
Press once for 10 seconds delay time (demo mode)
•
Press twice for 1 minute delay time
•
Press three times for 5 minutes delay time
Lockout
Lockout
•
Press four times for 15 minutes delay time
•
Press five times for 30 minutes delay time
•
Press six times to deactivate presence detection
a LED flashes 1 to 6 times to confirm.
Tip
Tip
4.
Press both keys simultaneously and hold for 8 seconds to permanently save the
If you do not press a key within a twenty second period during adjustment of
If you do not press a key within a twenty second period during adjustment of
setting.
constant lighting control, presence detection, lockout or automatic control,
constant lighting control, presence detection, lockout or automatic control,
a The LED extinguishes.
SensControl II switches back to operating mode and the modifications are not
SensControl II switches back to operating mode and the modifications are not
saved. If you have pressed keys erroneously, wait 20 seconds and repeat the
saved. If you have pressed keys erroneously, wait 20 seconds and repeat the
adjustment.
adjustment.
Dual-channel version
Dual-channel version
with separate indirect/direct light
with separate indirect/direct light
Indirect lighting
Indirect lighting
p Press and hold upper
p Press and hold upper
key until the desired
key until the desired
illuminance level is set.
illuminance level is set.
During dimming take care that you do not press both
During dimming take care that you do not press both
keys simultaneously, as in this case SensControl II
keys simultaneously, as in this case SensControl II
switches to setting mode.
switches to setting mode.
Adjustable values
Adjustable values
activated/deactivated
activated/deactivated
5 - 100 %
5 - 100 %
10 seconds (demo mode),
10 seconds (demo mode),
1, 5, 15, 30 minutes,
1, 5, 15, 30 minutes,
Presence detection deactivated
Presence detection deactivated
semi-automatic/ fully
semi-automatic/ fully
automatic
automatic
activated/deactivated
activated/deactivated
Direct lighting
Direct lighting
p Press and hold lower
p Press and hold lower
key until the desired
key until the desired
illuminance level is set.
illuminance level is set.
Factory setting
Factory setting
activated
activated
15 minutes
15 minutes
fully automatic
fully automatic
activated
activated
3 EN
www.zumtobel.com
www.zumtobel.com
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
