Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OPERATING INSTRUCTIONS
BS-3.9/1m QVGA CAMERA PROBE
ITEM NO.: 40 92 11
INTENDED USE
This product is a camera attachment for various endoscope main units from the Voltcraft
product range (see the compatibility list under "Technical data"). It is designed for visual
troubleshooting and inspection of voltage-free systems and installations. The flexible camera
neck permits the camera located on the tip to reach otherwise inaccessible positions. There
are two LEDs integrated in the camera head, permitting recording in dark spaces. The
brightness of the LEDs can be regulated via the connected endoscope main unit. The camera
neck and head are waterproof and thus suitable for use in voltage-free liquids (no acidic or
basic solutions). Use on persons or animals as well as in potentially explosive areas is not
permitted. The device is supplied with power via the connected endoscope main unit.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If
you use the product for purposes other than those described above, the product may be
damaged. In addition, improper use can cause hazards such as short circuiting, fire, electric
shock etc. Read the instructions carefully and keep them. Make this product available to third
parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
DELIVERY CONTENT
• QVGA camera probe
• Lens cap
• Operating instructions
SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Heed all legal regulations for operation of the product. Do not use the product for
the surveillance of persons!
b) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
If you are not sure about the correct connection or use, or if questions arise which are not
covered by these operating instructions, please do not hesitate to contact our technical
support or another qualified specialist.
Voltcraft®, Lindenweg 15, D-92242 Hirschau, Tel. +49 96 04 / 40 87 80
OPERATION
Hold the camera head and neck only in voltage-free liquids (no acidic or
basic solutions). The camera neck may not be submerged in water past the
marking "IP 67 max. water level" located on the plug, as the plug itself is not
waterproof.
The endoscope is suited for inspection only in voltage-free systems.
The camera head is made of metal and can cause short-circuiting. For
safety reasons, make sure all system components are voltage-free before
VERSION 06/13
inspection.
Do not exceed the minimum bending radius of 45 mm.
Place the included lens cap on the camera lens when the camera is no in use.
1. Carefully connect the product plug to the corresponding socket on your endoscope main
unit.
Make sure that the pins inside the plug are correctly aligned with the socket to prevent
their breaking off or bending.
2. Secure the connection using the fastening ring on the endoscope main unit.
3. Repeat these steps in reverse order to disconnect the product from your endoscope main
unit.
You can find further operating instructions, such as on regulation of LED brightness, in
the operating instructions of the endoscope main unit.
CLEANING
• Before cleaning, disconnect the product from the endoscope main unit.
• Use a small brush or cotton swab to clean the camera lens.
• Use a cloth, slightly damp with lukewarm water, to clean the camera neck.
DISPOSAL
Electronic devices are recyclable waste and must not be disposed of in the
household waste.
At the end of its service life, dispose of the product according to the relevant
statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
TECHNICAL DATA
Compatible with .................... BS-200XW, BS-250XWSD, BS-220XIP, BS-300XRSD, BS-50X,
..............................................
Resolution ............................. 320 x 240
Lighting ................................. 2 white LEDs
Illuminance ........................... max. 600 lux ±150 lux (at a distance of 20 mm)
Bending radius ...................... >45 mm
Protection type ...................... IP67
Field of view .......................... 54º
Focus .................................... 10 – 50 mm
Operating conditions ............. 0 to +45 ºC, 15 – 85 % RH
Storage conditions ................ -10 to +50 ºC, 15 – 85 % RH
Camera head Ø .................... 3.9 mm
Length................................... 104 cm ±2 cm
Weight .................................. approx. 50 g
Legal notice
These operating instructions are a publication by Voltcraft®, Lindenweg 15, D-92242 Hirschau/Germany, Phone +49 96 04 / 40 87 80
(www.voltcraft.de).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing
systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2013 by Voltcraft®
BS-100XIP, BS-250XIPSD
Werbung
