Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL BG-CG 18 B Bedienungsanleitung

Anleitung_BG_CG_18_B_SPK7:_
GB
6.1 Cutting grass
Allow the grass cutter to glide above the ground. The
best results are achieved when the lawn is dry.
When you notice a drop in cutting performance, re-
charge the tool immediately so that the battery does
not become fully discharged.
6.2 Trimming hedges
The tool can be used to trim small hedges and
shrubs.
Hold the tool slightly tilted in relation to the hedge
you want to cut.
First cut the sides from the bottom up, then cut the
top.
Watch out for foreign objects in or on the hedge
which could damage the blades.
When is the best time to trim hedges?
As a general rule, hedges which lose their leaves
in the autumn should be trimmed in June and
October.
Hedges which do not lose their leaves should be
cut in April and August.
6.3 Changing the blades
Important! Risk of injury!
To remove the blades, undo the screw on the
underside of the device (Fig. 6 and Fig. 10/Item 1).
Once you have removed the blade you will be able to
see the toothed wheels of the gear unit (Fig. 7). Take
care to make sure that no dirt gets into the gear unit
when you change the blade.
When you fit the hedge cutter blade, check the
position of the pin for the eccentric connector (Fig.
7/Item 1).
Take the hedge cutter blade and slide the eccentric
mount (Fig. 8/Item 1) into position so that the pin for
the eccentric connector and the eccentric mount fit
together precisely when assembled. To secure the
hedge cutter blade for cutting, slot it onto the guide
pins (Fig. 7/Item 2) and fasten it in place with the
screws (Fig. 10/ Item 1).
When you fit the grass cutter blade, check the
position of the pin for the eccentric connector (Fig.
7/Item 1) again.
Shift the eccentric mount (Fig. 9/Item 1) on the grass
cutter blade to the left or the right to find the position
at which the pin for the eccentric connector (Fig.
7/Item 1) and the eccentric mount (Fig. 9/Item 1)
match up. Then secure the cutter blade by tightening
the screw again.
12
09.07.2008 8:42 Uhr Seite 12
7. Cleaning, maintenance and ordering
of spare parts
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
A few drops of oil (e.g. sewing machine oil) will
improve the cutting performance of the blades,
but never apply any grease to the blades. To
ensure constant exact cutting it is also important
to remove grass remnants and dirt from between
the upper and lower blade.
Important!
Never clean the tool under running water - and
particularly never with high pressure - because
of the potential danger to persons and property.
Keep your cordless grass cutter and hedge
trimmer in a dry and frost-proof place. Choose a
place that children are unable to enter.
7.2 Maintenance
To achieve good results you should keep the
blades sharp at all times. In particular we
recommend that you immediately level off any
jags or ridges caused by stones or the like. The
tool should be thoroughly cleaned both before
and after use.
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info