Maintenance; Optional Accessories - Makita DBN500 Betriebsanleitung

Removing jammed nails
WARNING:
• Always make sure that the trigger is released, and the
battery cartridge and nails are removed before
removing jammed nails.
Remove hex bolts they are securing the driver guide
cover with the hex wrench.
Take the jammed nails from the nail guide groove that has
appeared.
Secure the driver guide cover with hex bolts in the correct
order. Tighten the hex bolt A, B and then C. (Fig. 16)
NOTE:
• After securing the driver guide cover, always make sure
that the driver guide cover actuates properly. If it does
not actuate properly, remove hex bolts and install the
driver guide cover again.
Nails (Fig. 17)
Handle nails and their box carefully. If the nails have been
handled roughly, they may be out of shape or their
connector breaks, causing poor nail feed.
Avoid storing nails in a very humid or hot place or place
exposed to direct sunlight. (Fig. 18)

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge and nails are removed before
attempting to perform inspection or maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Cleaning of magazine
When the pusher in the magazine does not move
smoothly because of dust, sand, chips or other foreign
matters, clean the magazine.
To remove the slide door, loosen the hex bolt on the
magazine. (Fig. 19)
Pull the pusher from the slide door and then remove the
stopper, sleeves and springs.
After cleaning, install the whole parts into the slide door.
To install them, take the following procedure. (Fig. 20)
1. Install the large spring into the slide door.
2. Install the parts onto the pusher in the correct order,
sleeve, small spring and then stopper.
3. Install the pusher with the other parts onto the slide
door.
NOTE:
• When you pull out the pusher from the slide door, the
parts in the slide door may bounce out.
• When you install the pusher with the other parts to the
slide door, make slight spaces between the pusher and
sleeves.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Nails
• Makita genuine battery and charger
• Safety goggles
NOTE:
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Vibration
The vibration total value determined according to
EN60745:
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been
measured in accordance with the standard test method
and may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of exposure in
the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool
is switched off and when it is running idle in addition to
the trigger time).
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Cordless Brad Nailer
Model No./Type: DBN500
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standards or standardised documents:
EN60745, EN792
ENG905-1
): 79 dB (A)
pA
ENG904-2
2
): 2.5 m/s or less
h
2
ENG901-1
ENH003-14
9