Makita DRC200Z Betriebsanleitung Seite 17

• Threads and hairs are tangled with the
drive wheels.
Remove them from the drive wheels
lamp flashes
(Fig. M-2).
4 times for each
• The Robotic Cleaner passed through
sequence
a confined area where its top surface
was pushed down.
This is not a malfunction.
• The Robotic Cleaner has overheated.
Turn the Robotic Cleaner OFF,
lamp flashes 5
remove the battery cartridge(s), and
or 7 times for each
wait for an hour. Use the Robotic
sequence
Cleaner only at room temperatures
not exceeding 40°C (104°F).
• The dust box or the filter has not been
and
installed.
lamps flash once
Install the dust box or the filter.
for each sequence
• The remaining battery charge was
and
not enough (
all lamps flash
cleaning.
once for each
Fully charge the battery cartridges.
sequence
• Threads and hairs are tangled in the
drive wheels.
Remove them from the drive wheels
(Fig. M-2).
and lamps
• The Robotic Cleaner passed through
light up
a confined area where its top surface
was pushed down.
This is not a malfunction.
• A sensor error has occurred.
and lamps
Turn the Robotic Cleaner OFF and
light up
then ON.
• An error has occurred in the Robotic
Cleaner.
and lamps
Turn the Robotic Cleaner OFF and
light up
then ON.
• Threads and hairs are tangled in the
lamp flashes
side brushes and main brush.
once for each
Remove them from the brushes (Figs.
sequence
A, N-3).
• The dust box is full of dust and dirt or
lamp the filter is clogged.
lights up Empty the dust box (Fig. K-2) and
clean the filter (Fig. K-5).
TROUBLESHOOTING
NOTE: If the problem persists after the remedial
action is taken, consult your nearest Makita Service
Center.
The lamps do
not light up
when you press
the
The Robotic
Cleaner does not
operate when you
press the button
on the Robotic
Cleaner or the
or ) to start
remote control.
The Robotic
Cleaner does not
operate.
The Robotic
Cleaner starts
operation
automatically.
The Robotic
Cleaner stops
operation during
cleaning.
The cruising speed
is not constant.
The Robotic
Cleaner does not
travel straight
forward.
The Robotic
Cleaner is hitting
obstacles more
frequently than
before.
The Robotic
Cleaner falls down
stairs or to a lower
floor.
The operating
sound is louder
than usual.
17 ENGLISH
Symptom
button.
Install the battery cartridges correctly.
Fully charge the battery cartridges.
Press the
Robotic Cleaner ON.
If the
lamp,
or Brush maintenance lamp lights
up or flashes, see "RESTORING THE
ROBOTIC CLEANER" to resolve the
problem.
If the pilot lamp flashes slowly, press
and hold the
the Robotic Cleaner until all indicators
go off, or press the
button on the remote control to clear
the timer.
• The auto-on timer has been activated.
Turn the Robotic Cleaner OFF, and
then remove any cords, strings, etc.
from the drive wheels.
If the Robotic Cleaner has gotten
stuck on a barrier or other obstacle,
move the Robotic Cleaner to a
different location.
• If an obstacle is detected, the Robotic
Cleaner will slow down as it takes time
to calculate a traveling direction. This
is not a malfunction of the Robotic
Cleaner.
Turn the Robotic Cleaner OFF, and
then remove any foreign objects
tangled in the drive wheels.
Clean the ultrasonic sensors.
Clean the ultrasonic sensors.
Clean the cliff sensors.
• The Robotic Cleaner may not avoid
differences in level of 5.5 cm or
less. This is not a malfunction of the
Robotic Cleaner.
Empty the dust box and clean the
filter, the side brushes, and the main
brush.
Cause/Remedy
button to turn the
Troubleshooting
Filter maintenance lamp,
POWER button on
POWER OFF