Makita DTP131 Betriebsanleitung Seite 9

Changing the torque setting (screwdriver
mode " ")
The fastening torque can be adjusted by pressing the
button in screwdriver mode.
The numbers on the LED display shows torque setting.
The fastening torque is minimum at the number 1 and
maximum at the number 9. The indication "P" is a special
mode for fastening self drilling screws.
Every time the button
changes from 1 to 9 and P, and then returns to 1.
The torque setting changes fast by keeping pressing the
button.
P mode is suitable for fastening self drilling screws into
steel plates in the following conditions.
• With speed change lever at "2" side, fastening max.
4 mm screw into total max. 3.2 mm steel plates.
• With speed change lever at "1" side, fastening max.
5 mm screw.
Before an actual operation, drive a trial screw into your
material or a piece of duplicate material to determine
which torque level is required for a particular application.
First, try to fasten the screw at "1". Then increase the
number to continue fastening. Hold the tool firmly during
operation.
CAUTION:
• Don't fasten the machine screw on P mode. It may
twist your wrist suddenly and result in personal injury.
NOTE:
• Make sure to check the number on LED display before
operation. If the number is not indicated, contact your
nearest Makita service center.
• When the remaining battery capacity gets low in the
screwdriver mode, the light flashes a few times when
fastening the screw completely. In this case, recharge
the battery. If you keep operating, you may not obtain
the desired torque.
• During pulling the switch trigger, the torque setting can-
not be changed.
• For approximately one minute after releasing the
switch trigger, the torque setting can be changed. If you
want to change the torque setting after that, pull the
switch trigger again.
• The number of torque setting does not mean specific
torque rate.
Empty signal for remaining battery capacity
(Fig. 11)
(Country specific)
The remaining battery capacity will be signaled on the
LED display when pulling the switch trigger.
The remaining battery capacity is shown as the following
table.
is pressed, the torque setting
LED indicator status
012273
NOTE:
• When the LED display goes off, the tool is turned off to
save the battery power. To check the remaining battery
capacity, slightly pull the switch trigger.
• The LED display goes off approximately one minute
after releasing the switch trigger.
• When the temperature of the tool gets high, the light
flashes once per second for one minute, and then the
LED display goes off. In this case, cool down the tool
before operation.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the bat-
tery cartridge is removed before carrying out any work
on the tool.
Installing or removing driver/drill/socket bit
(Fig. 12)
Use only the driver/drill/socket bit shown in the figure. Do
not use any other driver/drill/socket bit.
For tool with shallow bit hole
Use only these type of bit. Follow the
A = 12 mm
procedure (1).
B = 9 mm
(Note) Bit-piece is not necessary.
006348
For tool with deep bit hole
A = 17 mm To install these types of bits, follow the
B = 14 mm procedure (1).
To install these types of bits, follow the
A = 12 mm procedure (2).
B = 9 mm (Note) Bit-piece is necessary for install-
ing the bit.
011405
1. To install the bit, pull the sleeve and insert the bit into
the sleeve as far as it will go. Then release the
sleeve to secure the bit. (Fig. 13)
2. To install the bit, insert the bit-piece and bit into the
sleeve as far as it will go. The bit-piece should be
inserted into the sleeve with its pointed end facing
in. Then release the sleeve to secure the bit.
(Fig. 14)
Remaining battery capacity
About 50% or more
About 20% – 50%
About less than 20%
9