Troubleshooting; Technical Specifications - BRAX X 2400.2 Bedienungsanleitung

Troubleshooting

SYMPTOM
POSSIBLE CAUSES
The amplifier cannot
12-volt positive supply lead line interrupted.
be switched on.
Amplifier not correctly connected to ground/chassis.
Power supply to the remote terminal interrupted.
LEDs light up green
The cinch input cables are not inserted, or the speakers
but no sound can be
are not connected.
heard.
There is a faulty connection between the RCA terminal
and the control unit.
One channel may not be properly connected to the con-
Only one channel is
trol unit or speaker.
operating.
One channel has overheated - LED lights up red.
Speaker wiring is faulty (short circuit between the wires
or with the chassis of the vehicle); LED lights up red.
One speaker is faulty.
Parasitics in the cinch cable.
Interference noise
Parasitics in the power supply cabling.
from the engine.
Feedback interference from the chassis to the control
unit (radio/tuner).
Please consult your dealer in relation to all other installation problems.
Once again we would ask you to have your dealer perform the installation work. He will be able to guarantee to you that this
high-quality amplifier has been correctly installed. Moreover, verification of correct installation by specialist is a prerequisite for
the lifetime warranty of your amplifier.

Technical Specifications

Continuous power rating
at 4 Ohm per channel
at 2 Ohm per channel
bridged into 4 Ohm load
Total harmonic distortion (THD)
Signal to noise ratio
Damping factor at 4 ohms
Frequency response
TIM Distortion
Input Sensivity
External fuse size
Input impedance
Dimensions (H x W x D) in mm
Weight net.
X2000.2
2 x 190 Watts
2 x 370 Watts
1 x 740 Watts
< 0,002%
> 105 dB
> 400
20 Hz-20 kHz, +/- 0,2 dB 20 Hz-20 kHz, +/- 0,2 dB
< 0,016 %
300 mV-7,5 V
100 A
10 kOhms
53 x 238 x 470
7,4 kg
REMEDIES
Check the power supply fuses and cabling.
Check the connection to the chassis metal
Check the 12-volt remote output of your control unit (radio/tuner).
Check that all the cables are properly inserted or screw-fixed.
Check the wiring and replace if necessary.
Check the wiring connections, or swap the channels around.
Turn the amplifier off and allow it to cool for a good while. Then switch it
on again. If the LED is still showing red, consult your dealer.
Check the speaker wires and the speakers themselves for short-circuiting,
and rectify as necessary.
Replace the defective speaker with a new one.
Check the connections (screen/shield).
Replace the cable with screened BRAX POWER TRAX cable. Consult your
dealer.
Select an optimum central ground point to serve the entire power supply
system of your vehicle, including the control unit (radio/tuner).
X2400.2
GRAPHIC EDITION
4 x 110 Watts
4 x 200 Watts
2 x 400 Watts
< 0,002%
> 105 dB
> 400
20 Hz-20 kHz, +/- 0,2 dB
< 0,014 %
300 mV-7,5 V
100 A
10 kOhms
53 x 238 x 470
7,4 kg
15
X2000.2
GRAPHIC EDITION
2 x 265 Watts 4 x 135 Watts
2 x 440 Watts 4 x 235 Watts
1 x 880 Watts 2 x 470 Watts
< 0,001%
> 110 dB
>600
20 Hz-20 kHz, +/- 0,2 dB
< 0,009 %
300 mV-7,5 V 300 mV-7,5 V
100 A
10 kOhms
53 x 238 x 473 53 x 238 x 473
8,2 kg
X2400.2
<0,001%
>110dB
>400
< 0,009 %
100 A
10 kOhms
8,2 kg