Herunterladen Inhalt Inhalt Diese Seite drucken

Einsatzhinweise / Special Aspects Of Application - BEKOMAT 3 CO V Installation Und Betriebsanleitung

Inhaltsverzeichnis

Werbung

Beachten Sie:
Der Betriebsdruck der Anlage darf nur zwischen 0,1 und
1,8 bar (abs) betragen!
Durch die V-Versionen wird der Einsatzbereich der BEKOMAT-
Grundtypen für den Druckbereich von 0,1 bis 1,8 bar (abs)
erweitert. Oberhalb dieses Druckbereiches sind die V-Versionen
nicht einsetzbar, da die Verschlusssicherheit des Membran-
ventiles dann nicht mehr gewährleistet werden kann.
V-Versionen sind besonders für die Ableitung von Kondensat
oder anderen abgeschiedenen Medien aus Vakuumsystemen
und für unter Normalatmosphäre ablaufende verfahrenstech-
nische Prozesse geeignet.
Beachten Sie:
Aggressive Medien erfordern entsprechende Gehäuse- und
Armaturenmaterialien!
Entsprechend der abzuleitenden flüssigen Medien gibt es
unterschiedliche Ausführungen der Gehäuse und Armaturen:
- BEKOMAT-Gehäuse:
- Absperrarmaturen:
Beachten Sie:
Steuerluft oder -gas dringt beim Schalten in das Vaku-
umsystem ein!
Beim Schalten des BEKOMAT V kommt es durch die ange-
schlossene Hilfsenergie Druckluft (oder -gas) zum Eindringen
von Restluft (oder -gas) in das Vakuum-system. Bei BEKOMAT
3 V - Versionen sind dies bei 6 bar Steuerdruck ca. 2 bis 3 l,
bei BEKOMAT 6 V - Versionen bis 15 l Normalvolumen.
BEKOMAT V dürfen daher nur in solchen Systemen zur
Ableitung eingesetzt werden, in denen durch diese Mengen
keine technischen, verfahrenstechnischen oder sicher-
heitstechnischen Probleme entstehen (z.B. Entstehen von
explosiven Gasgemischen).
Beachten Sie:
Bei großen Flüssigkeitsmengen ist zur einwandfreien
Ableitung eine Luft-Pendelleitung erforderlich!
Im Normalfall ist die Rohrleitungsinstallation des BEKOMAT
V über einen Zufluss ausreichend. Können zyklisch große
Flüssigkeitsmengen anfallen, ist die Installation des BEKO-
MAT V mit Luft-Pendelleitung vorzunehmen. Dies muss bei
der Bestellung mit angegeben werden, da auch für die
Luft-Pendelleitung bei der Herstellung des Gerätes eine Ab-
sperrarmatur anzubringen ist.
Beachten Sie:
Der Membrandeckel ist eine Sonderanfertigung!
Der Hauptunterschied der BEKOMAT V besteht neben den
zusätzlichen Absperrarmaturen im konstruktiv völlig neu ge-
stalteten Membrandeckel. Dieser ist sowohl Ansteuerelement
für die Absperrarmaturen als auch Membrandeckel mit den
bisherigen Aufnahmen für die Membrane und das Magnetventil
zur Gewährleistung der Ableiterfunktion.
BEKOMAT 3 CO V, 3 E V, 6 CO V, 6 E V

Einsatzhinweise / Special aspects of application

Aluminium,
Aluminium mit Hartcoat,
Edelstahl
Messing, Edelstahl
Please note:
The operating pressure of the plant must be between
0.1 and 1.8 bar (abs.)!
The V variants extend the field of application of the basic
BEKOMAT units by permitting operation in the pressure
range from 0.1 to 1.8 bar (abs.). Above this pressure range,
the V variants should not be used since this may impair the
sealing capacity of the diaphragm valve.
The V variants are particularly suitable for the discharge of
condensate or other separated media from vacuum systems
and for processes carried out under standard atmospheric
conditions.
Please note:
Aggressive media require correspondingly resistant
materials for housing and valves!
- BEKOMAT housings:
Aluminium,
Aluminium with Hardcoating,
Stainless steel
- Shutoff valves:
Brass, Stainless steel
Please note:
Control air or gas penetrates into the VACuum system
during switching!
During switching of the BEKOMAT V unit, residual air or gas
of the compressed air or gas providing auxiliary energy is
able to penetrate into the vacuum system. In the case of the
BEKOMAT 3 V variants this amounts to approximately 2 to 3
litres with a control pressure of 6 bar, while the BEKOMAT 6
V variants have a standard volume of 15 litres.
The BEKOMAT V units must therefore only be used for
discharge functions in systems where it is certain that
these amounts cannot cause any technical, processing
or safety problems (e.g., formation of explosive gas
mixtures).
Please note:
With larger quantities of liquid it will be necessary to
provide a balance air pipe to ensure correct discharge.
Normally, it will be sufficient to connect the piping of the BE-
KOMAT V unit to an inflow point. If cyclic operation is likely
to produce large quantities of liquid, the installation of the
BEKOMAT V unit should be carried out including a balance
air pipe. This should be stated when ordering, since the
BEKOMAT unit has to be manufactured with a corresponding
shutoff device for the balance air pipe.
Please note:
The diaphragm cap is a special construction!
Apart from the additional shutoff devices, the main diffe-
rence of the BEKOMAT V variants consists of a diaphragm
cap with a completely new design. It serves both as an
activating element for the shutoff valves and as a diaphragm
cap with the normal arrangements for the diaphragm and the
solenoid valve to ensure the discharge function.
5

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis