Vivanco UR S2 Bedienungsanleitung Seite 2

Manual code search
1.
be controlled. Program is running.
2.
press the SET button, keep it pressed
and then press the required appliance
button, e.g. TV, additionally until the
lamp (LED) lights constantly.
3.
control
controlled.
4.
button once. The lamp (LED) blinks. B
5.
(appliance on/off) button repeatedly
for testing the next code, approx.
every 1,5 seconds, until the appliance,
e.g. your TV reacts by power off.
- If your appliance has switched itself
off you must switch it back on again,
e.g. on the appliance or with the
original remote control, to continue
searching. - When your appliance
reacts you can also try out other
buttons
search. If some buttons do not work
properly, simply continue searching
with ON/OFF.
6.
reacts correctly, press the appliance
button, e.g. TV, and end the search.
The lamp (LED) goes out.
- The UR S2 continues with the search
at the point where you interrupted it. .
The code last entered remains stored.
The search stops after approx. 30
seconds of inactivity.
Automatic code search
Your remote control finds the correct
settings
seconds:
1.
be controlled. A channel number, for
example, appears in the display of
your satellite receiver.
2.
press the required appliance button,
e.g. DVB briefly.
3.
5 seconds until the lamp (LED) starts
to blink.
Downloaded from www.Manualslib.com
UR S2 UNIVERSAL TV- DVB CONTROLLER
Switch on the appliance to
To prepare code search,
Then point the remote
at the appliance
Briefly press the
Press the ON/OFF
without interrupting
When your appliance
almost automatically
Switch on the appliance to
To start the code search,
Then press SET for about
Vivanco GmbH, D-22926 Ahrensburg, E-Mail
manuals search engine
4.
control at
controlled while the remote control
emits a different ON/OFF signal every
second.
5.
reacts, press SET within 1-2 seconds,
to end the search. – If you ended the
search too late, continue to search
to be using the Manual Code Search (see
above).
6.
SET
code setting by trying to control, for
example, your DVB appliance. If it
does not work correctly, please try the
code search again. The code search
then begins with the next code in the
sequence. - Remember to switch your
appliance, e.g. DVB, back on again if
you wish to continue searching.
Code identification
You can read off the 3-digit codes you
have set at any time:
1.
of the appliance which code you want
the
to read off, e.g. TV.
2.
1,2,3, depending on the part of the
code you want to read off. For
example, if you press SET+1 after TV
and the code 176 (in this example)
has been set, the lamp blinks once
after SET+1 is released to show that
the hundred figure is 1.
you have to do is count. The ten figure
is indicated after SET+2 is released,
e.g. it blinks 7 times for the 7 in 176.
The one figure is indicated after
SET+3 is released, e.g. it blinks 6
times for the 6 in 176.
in
- Please
compartment and write down the
found codes, for later use, onto the
sticker placed at the innerside of the
compartment door.
Operation
You operate your appliances basically
in exactly the same way as if you were
using the original remote controls,
except that you must first press an
appliance button (TV, DVB, etc.) to
control the required appliance. As the
: hotline@vivanco.de
Then point the remote
the appliance to
When your appliance
Finally, test the control
Press the appliance button
Press the SET button and
open the battery
,
be
All
2