Installation - HQ Power VDP900HZ Bedienungsanleitung

4. Ins tallation
• Remov ve all packing m
remove ed.
• Clean t the spray nozzle
• Place t he VDL900HZ
• Pour hi igh quality smok
fluid lev vel. Do not ove
• Connec ct the remote co
5. Use e
a) The Device
• Plug th he remote contro
power cord.
• Turn on n the power swi
• The red d light on the re
• The de vice must warm
minute es.
• The gre een light on the
Remot te Control").
b) The Remote Contr
Please re efer the illustrat
1 pow wer LED
smo oke output ever
2
30 min)
3 out put volume
4 fixe ed time open LE
6. Not tes
The V VDP900HZ doe
pum p will continue
• If you e experience low
Check the fluid level, t
working g properly, plug
operati ion to avoid per
before transporting th
• Using t the device will p
• A little smoke may con
7. DMX X Connectio
a. DMX5 12 Connection
Connect an XLR cable to
pin XLR i nput of the VDP
cable sho ould be a two-co
b. DMX-5 512 Chain with
c. DMX S Start Address
All DMX-c controlled devic
This start t address is the
Enter the e correct numbe
You can u use the same st
device.
09.11.201 0
aterial from the e shipping box. C
e and make sure e nothing is obs
horizontally on a flat surface. R
ke liquid (VDLH HLH5) into the t
rfill. Place the c cap back on the
ontrol into the s slot at the back
ol into the slot a at the back of th
itch located at t the back of the
emote control w will light up.
m up. The period d depends on th
e remote control l will go up once
rol
ion on page 2.
ry x minutes (m max.
ED
es not feature a an automatic
e working. Alw ways monitor t
device can su uffer damage w
output, mechan nical noise or no
the external fus se, the remote c
g in the unit aga ain. If the device
rmanent damag e. Return the de
e unit.
produce water d rops at the noz
ntinue to escape e from the nozz
on
n
o the female 3-p pin XLR output o
P900HZ. Multip ple VDP900HZs
ore screened ca able with XLR in
h Termination n
A DMX term minator is recom
to run a lon g distance or is
The termina ator prevents co
noise. The D DMX terminator
between pin ns 2 and 3, whic
the last dev vice in the chain
ces need a digita al start address
channel numbe er from which th
er and read it fro om the display
tarting address for a whole gro
VDP90 0HZ
Check that all fo
structing the ou
Remove the liqu
tank, being care
liquid tank and
of the device.
he device. Plug
device.
he conditions bu
e the machine is
5 output LED
successive s
6
seconds)
7 heated over
8 spray button
stop function
the tank fluid
when run with
o output at all, u
control and the
e will not functi
evice to your de
zle. This is perf
zle after operatio
of your controlle
s can be linked
put and output
mmended for ins
in an electrical
orruption of the
is simply an XL
ch is then plugg
. Please see illu
so that the cor
he device starts
located on the b
oup of devices o
4
oam and plastic c padding is
tput.
uid tank cap.
eful not to excee ed the maximum
tighten.
the device into the mains usin
ut should not tak ke more than 10
s ready to opera ate (see "The
spraying for x se econds (max. 1
r LED
n
when running g out of fluid; t
level during o operation as th
hout fluid!
unplug the devi ce immediately
power cord. If a all appears to be
on after 30 seco onds, discontinu
ealer. Remembe er to drain the t
fectly normal.
on.
er and the other r side to the ma
through serial l inking. The link
connectors.
tallations where e the DMX cable
ly noisy environ nment (e.g. disc
digital control s signal by electri
LR plug with a 1 120Ω resistor
ged into the XLR R output socket
ustration.
rrect device resp ponds to the sig
s to "listen" to th he DMX controll
base of the VDP P900HZ.
r enter an indiv vidual one for ev
m
g the
0
5
the
he
.
e
ue
tank
ale 3-
king
e has
cos).
cal
of
gnals.
ler.
very
©Vellema an nv