Before Starting The Equipment - HERKULES ZKG 305 L Originalbetriebsanleitung

Anleitung_ZKG_305_L_SPK7:_
GB
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 61029.
Vibration emission value a = 1,297 m/s 2
h
K uncertainty = 1,5 m/s 2
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.

6. Before starting the equipment

6.1 General
The machine must be firmly mounted in working
position, e.g. on a workbench, the base frame
supplied with the machine, or similar.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
24
02.09.2010 14:09 Uhr
86 dB(A) that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
3 dB
Before you connect the machine to the power
99 dB(A)
supply, make sure the data on the rating plate is
3 dB
the same as that for your mains.
6.2 Assembling the saw (Fig. 1-3; 6)
To adjust the turntable (17), loosen the locking
grip (14) by approx. 2 turns, which frees the
turntable (17).
Press the locking lever (13), turn the turntable (17)
and scale pointer (15) to the desired angular
setting on the dial (16) and lock into place with
the locking grip (14). The saw has locking
positions at angular positions of -45°, -30°, -22,5°,
-15°, 0°, 15°, 22,5°, 30°, 45° and 60° at which the
locking lever can be engaged.
To release the saw from its position at the bottom,
pull the locking pin (27) out of the motor mounting
while pressing down lightly on the machine head
(4). Turn the locking pin (27) through 90° before
you release it so that the saw remains released.
Swing the machine head (4) up until the release
lever (3) latches into place.
The clamping device (8) can be fitted on either the
left or right of the fixed saw bench (18).
Undo the locking screws for the workpiece
support (30).
Guide the roller support with limit stop (9) over
one of the holding bars for the roller support (10)
and secure it to the fixed saw bench (18),
tightening the appropriate locking screw (30) (Fig.
6).
Fit the second holding bar for the roller support
(10) on the opposite side of the saw and secure it
with the appropriate locking screw (30).
When the locking screw (22) is loosened, you can
tilt the machine head (4) to the left by up to 45°.
If the saw is used without a base frame, the
support foot (32) is designed to ensure that the
saw cannot tip forwards during use. To do this,
unscrew the support foot (32) until it touches the
support surface of the saw.
6.3 Assembling the base frame and bolting the
saw to the base frame (Fig. 4 – 25)
1. Place the support feet (A) from underneath into
the intermediate struts (C) as shown in Fig. 7.
Ensure that the rubber feet are aligned on the
support feet (A) so that their support surfaces are
straight.
2. Bolt the support feet (A) to the intermediate struts
(C) as shown in Fig. 8 – 9 using the screws (N),
washers (H) and nuts (G).
3. Guide the side parts (B) from the top over the
intermediate struts (C) (Fig. 10).
Seite 24