Technical Data; Before Putting The Machine Into Operation; Assembly And Operation - HERKULES ZGS 33-- UG Bedienungsanleitung

Anleitung ZGS 3300 UG_SPK7:_
GB
at the workplace include the duration of impact, the
type of room, and other sources of noise etc., e.g.
the number of machines and other neighbouring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved."

5. Technical data

Asynchronous motor 230 V ~ 50 Hz
Output 1600 W
Operating mode
Idle speed n 4200 min
0
Carbide-tipped saw blade ø 305 x ø 30 x 3.2 mm
Number of teeth
Tilting range -45° / 0° / +45°
Mitre cuts 0° to 45° to the left
Saw bed support 515 x 360 mm
Sawing width at 90° 330 x 102 mm
Sawing width at 45° 230 x 102 mm
Sawing width at 2 x 45°
(double mitre cuts) 230 x 65 mm
Safety insulated
Weight 36,2 kg
6. Before putting the machine into
operation
The machine must be set up where it can stand
securely, i.e. it should be bolted to a workbench,
a universal base frame or similar.
All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
10
06.06.2007 14:52 Uhr
All manuals and user guides at all-guides.com
Important:
This machine was exactly adjusted before it left the
factory. For the best results you should check the
accuracy of the following settings and make
corrections as necessary.
6.1 Setting the angle stop to 90° and 45° (Fig.
5/6/7)
Release the angle clamping lever (13) and move
the cutting head (4) all the way to the right.
Secure the angle clamping lever (13).
Use an angular stop (a/b) to set the blade at 90°
in relation to the table.
If an adjustment is necessary, undo the locknut
S1 (d) and turn the screw (c) so that the blade
makes an angle of 90° with the table.
-1
Tighten the locknut (d).
Use the screw (c) to set the angle indicator (15)
60
to 0.
Use the same procedure to set the stop to 45°,
but instead move the cutting head to the left and
use the left screw (e).
6.2 Setting the stop face (Fig. 12)
Lower the cutting head and press in the locking
button (16). Make sure that the table shows a
miter angle of 0°.
Place an angular stop against the stop face and
II / ®
the saw blade.
If the blade does not touch the angular stop,
undo the three screws (33).
Adjust the stop face so that it touches the angle
gage full-face. Retighten the screws.

7. Assembly and operation

Always place the workpiece against the stop face. A
twisted and bent workpiece that cannot be held flat
on the table or against the stop face may catch on
the blade and should not be used. Keep your hands
out of the sawing zone. The entire table area is out of
bounds for hands. It is marked with "No Hands"
signs.
7.1 Fitting the clamping device and extension
supports (Fig. 1/3/4)
Always use the clamping device (19) to secure
the workpiece in position. Insert the clamping
device in one of the mounts (30) provided and
fasten it in place with the clamping screw.
Insert the extension supports on the left and right
in the mounts (29) provided in the base plate
and tighten the clamping screw.
The standard end stop (18) can be used for
repeat cuts. In this case, slip the end stop onto
Seite 10