KIKKA BOO STARK Gebrauchsanweisung Seite 11

Step 2: Use ISOFIX to secure the seat to the car seat, make sure the ISO FIX lock display window appears green, and then slowly push
the seat onto the back of the car seat until completely tted.
Step 3: The top strap of the seat is hung through the middle of the head of the car seat to the corresponding hook on the car (on the
node suggested in the automaker's manual). Tighten the tape of the top strap until the top strap regulator appears green, while
ensuring that the top strap is xed and tightened.
3.2.Installation of Child Seats (Group O+ : 0-13kg)-Option 2 for car without lso x
This restraint is suitable for children with weight 0-13kg, rearward facing installation .
Step 1: Adjust the seat to the fully reclined and then rotate the seat body 180 degree .
Step 2: Place the child seat centrally onto the passenger seat and the front of the child seat must be pushed rmly against the back of
the vehicle seat .
Step 3: Pull o approximately a meter of lap and diagonal belt and diagonal belt and route the two belts as follows:
Diagonal section : Pull the diagonal section through the slot at top of the seat backrest and wrap it around the back of the seat.
Lap section : rst release the buck and get o the cushion, then thread the lap section through the child seat, pay attention the lap
belt not to interfere the child seat belts.
3.3.Then insert the lap and diagonal belt onto the vehicle seat belt buckle .You will hear a click when it's correctly inserted. Pull on it
to check it is securely tted.
IV. INSTALLATION OF CHILD SEATS (GROUP I: 9-18KG)
This product is suitable for children with weight in 9-18kg.
Step 1: Use the three-point seat belt as shown in gure 4. To pass through the3-point seat belt, tighten the seat belt, and fasten the
child seat to the car seat. Then the sleeping pad is placed in the children's seat to improve the comfort of the use.
Step 2: place the child in the child's seat, buckle and pull out, check the shoulder strap and the height of the headrest.
Note: Do not twist the ribbon.
V. INSTALLATION OF CHILD SEATS (GROUP II,III: 15-36KG)
This product is suitable for children with weight in 15-36kg. (please refer to next item for removal of seat belts and buckles)
Put the child in the child seat and use the car at three points Seat belts fasten children's and children's seats to car seats.
Note: Do not twist the ribbon.
VI. REMOVAL OF SEAT BELTS AND BUCKLES
Step 1: Remove the straps of the straps as shown in gure
6.1,6.2,6.3,6.4.
Step 2: As shown in gure 6.5,6.6,6.7 to loosen the buckle and remove the sleeping pad and crotch pad, with shoulder straps stacked
under the sleeve. Remove the sun-shaped iron from the base of the seat and remove it from the buckle.
VII. MAINTENANCE AND CLEANING
THE ROUTINE MAINTENANCE
• During daily use, children's seat wear and tear need to be checked. In the event of an accident, the seat needs to be replaced.
• When not using child safety seats, place them in a dry, ventilated place to avoid damp and moldy seats.
• If dust is found on the surface of the child's seat, dry the seat belt and plastic parts with a damp sponge and then dry by ventilation.
• If you drop food or drink onto your seat belt, remove it and rinse it with warm water, then dry by ventilation.
• If you want to clean the entire seat cover, please refer to the 6.2 washing instructions.
THE WASH CARE INSTRUCTION
Solvents, chemical cleaners and lubricants are prohibited for any part of this product.
Hand washable, water temperature is less than 30 degrees. No drying, No ironing,Unbleached
THE REMOVAL AND DRESSING OF THE FABRIC COVER
1. Remove shoulder straps and shoulder covers;
2. Release the buckle rst, then remove the crotch pad and sleeping pad. ( gure 7.1)
3. Unbutton the headrest and base, respectively, and remove the sleeve. ( gure 7.2)
Note: if you need to install the cover again, please operate in reverse order of removal.
ENGLISH