Herunterladen Inhalt Inhalt Diese Seite drucken

Safety Regulations; Proper Use - EINHELL DTA 25/2 Originalbetriebsanleitung

Druckluft-tacker/-nagler
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
Anleitung_DTA_25_2_SPK1:_
GB
Important!
When using equipment, a few safety precautions
must be observed to avoid injuries and damage.
Please read the complete operating manual with due
care. Keep this manual in a safe place, so that the
information is available at all times. If you give the
equipment to any other person, give them these
operating instructions as well.
We accept no liability for damage or accidents which
arise due to non-observance of these instructions
and the safety information.

1. Safety regulations

CAUTION!
Read all safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
Take suitable precautions to protect yourself and
your environment from potential hazards.
Take suitable precautions to protect yourself and
your environment from potential hazards.
Never put the stapler to any use other than that
intended.
Keep pneumatic tools safe from children.
Always concentrate while you work. Do not work
if you are tired.
Use only a quick-release coupling to connect up
the air supply.
It is imperative to use a pressure reducer to set
the working pressure.
Never use oxygen or combustible gases as an
energy source.
Always disconnect the tool from the air supply
before carrying out any repairs or maintenance
work.
Use only original replacement parts.
Wear the necessary protective clothing,
particularly goggles and safety gloves, when
working with the stapler.
Do not exceed a maximum pressure of 6 bar.
Never point the stapler at any persons when it is
connected up and loaded.
Do not remove any protective devices or contact
guards.
Never leave the tool unattended when loaded.
Never use defective tools.
Use only original Einhell staples/nails.
8
28.10.2009
13:55 Uhr
Seite 8
When the tool is disconnected it must not be
under any pressure.
Never use the tool without staples.
Never point an operational stapler directly at
yourself or at any other person.
Whilst working with the stapler, hold it in such a
way that your head and body cannot be injured
in case of kickback caused by disruption of the
power supply or by hard areas of the workpiece.
Never trigger the stapler into the open air. This is
important to avoid the hazards of free-flying
staples and of overloading the appliance.
For the purposes of transportation, the stapler
must be disconnected from the compressed-air
system, especially if you are using a ladder or
are adopting an unusual posture.
In the workplace, carry the stapler only by its
handle and ensure that the trigger is inactivated.
Make allowance for the workplace conditions.
Staples can potentially go straight through thin
workpieces or they can slide off workpieces
when working on corners and edges, thus
putting persons at risk.
For you own personal safety, always use suitable
protective equipment such as, for example,
hearing and eye protection.
2. Layout (Fig. 1)
A
trigger lever
B
magazine
C magazine lever
D plug-in nipple for the air supply
E
air connection
F
Swivel air-outlet

3. Proper use

The stapler is a pneumatic tool for universal service.
The exhaust air leaves the housing to the front.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the
manufacturer will be liable for any damage or injuries
of any kind caused as a result of this.
Please note that our equipment has not been
designed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

41.377.55

Inhaltsverzeichnis