Würth STP 150 POWER-S Originalbetriebsanleitung Seite 12

❏ If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
Power tool use and care
❏ Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
❏ Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous and
must be repaired.
❏ Disconnect the plug from the power source
and/or the battery pack from the power
tool before making any adjustments,
changing accessories, or storing power
tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
❏ Store idle power tools out of the reach of
children and do not allow persons unfamil-
iar with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
❏ Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tool's operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
❏ Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
❏ Use the power tool, accessories and tool
bits etc. in accordance with these instruc-
tions, taking into account the working con-
ditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous situa-
tion.
Service
❏ Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Safety Warnings for Jigsaws
❏ Hold power tool by insulated gripping sur-
faces, when performing an operation
where the cutting accessory may contact
hidden wiring or its own cord. Cutting acces-
sory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give
the operator an electric shock.
Additional Safety and
Working Instructions
❏ Keep hands away from the sawing range.
Do not reach under the workpiece. Contact
with the saw blade can lead to injuries.
❏ Apply the machine to the workpiece only
when switched on. Otherwise there is danger of
kickback when the cutting tool jams in the workpiece.
❏ Pay attention that the base plate rests
securely on the material while sawing. A
jammed saw blade can break or lead to kickback.
❏ When the cut is completed, switch off the
machine and then pull the saw blade out of
the cut only after it has come to a standstill.
In this manner you can avoid kickback and can
place down the machine securely.
❏ Use only undamaged saw blades that are
in perfect condition. Bent or dull saw blades
can break, negatively influence the cut, or lead to
kickback.
❏ Do not brake the saw blade to a stop by
applying side pressure after switching off.
The saw blade can be damaged, break or cause
kickback.
❏ Use suitable detectors to determine if utility
lines are hidden in the work area or call
the local utility company for assistance.
Contact with electric lines can lead to fire and elec-
tric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage or may cause an electric shock.
❏ Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
❏ Always wait until the machine has come to
a complete stop before placing it down. The
tool insert can jam and lead to loss of control over
the power tool.
❏ Before any work on the machine itself, pull
the mains plug.
12