Makita PDC1200 Betriebsanleitung Seite 15

Connecting the unit to the tool or
machine
1. Remove the battery from the base plate of the
shoulder harness assembly.
2. Pull out the cord from either left or right side of the
battery. When pulling out the cord, be sure to set the
cord in the holders as shown in the figure.
► Fig.18: 1. Cord 2. Holder
3. Attach the battery to the base plate of the shoulder
harness assembly.
4. Put on the unit.
5. Insert the plug of the adapter or power tool/
machine into the socket of the battery all the way so that
the arrow mark on the plug is aligned with that on the
socket.
► Fig.19: 1. Plug 2. Socket 3. Arrow mark
NOTICE:
When disconnecting the plug and
socket, do not hold the cords but hold the plug
and socket. Otherwise, the cords may be damaged
and cause a malfunction of the unit.
NOTE: The plug and socket are disconnected if a
certain load is applied.
6. Install the adapters to the tool or machine in the
same way as the battery cartridge.
► Fig.20: 1. Adapter
NOTICE:
For 36 V (18 V x 2) battery-powered tool
or machine, use the adapters for 36 V (18 V x 2).
For direct connection type tool or machine, no
adapter is required.
NOTICE:
When installing adapters to the tool or
machine, be sure to install the adapter equipped
with 2 cords to the location shown in the figure.
If you install the adapters incorrectly, the adapter
equipped with 2 cords cannot be inserted all the
way. In this case, do not insert the adapter forci-
bly. Otherwise, the tool or machine may be damaged.
► Fig.21: 1. Adapter with 2 cords
► Fig.22: 1. Adapter with 2 cords
NOTE: The direction of the cord of the adapter can be
changed in the range of approximately 180 degrees.
7. Press the power button to turn the power on. To
turn the power off, press the power button for a few
seconds.
► Fig.23: 1. Power button
Using the cord holders
CAUTION:
Attach only the cord of the battery
to the cord holders. Do not attach the cord of the
adapters or power tool/machine to the cord hold-
ers. Attaching the cord of the adapters or power tool/
machine may invite accident and cause an injury.
► Fig.24
► Fig.25
You can attach the cord of the battery to the cord hold-
ers as shown in the figure.
► Fig.26: 1. Cord holder
You can also attach the cord using only the cord holder
of the waist belt as shown in the figure.
► Fig.27: 1. Cord holder
The cord holders can be attached on either left or right
side of the shoulder harness and waist belt.
► Fig.28: 1. Part to be attached the cord holder
CAUTION:
Be sure to attach the cord to the
shoulder harness on the left side only or right
side only so that the cord does not cross the
shoulder harness.
► Fig.29
Using the hanging band
Optional accessory
You can use the hanging band for cordless grass trim-
mer with this unit.
Attaching the hanging band
1. Attach the hooks of the hanging band to the rings
of the shoulder harness or waist belt as shown in the
figure. Select the type of band and the connecting
method appropriate for your usage.
► Fig.30: 1. Ring 2. Hook
► Fig.31: 1. Ring 2. Hook
► Fig.32: 1. Ring 2. Hook
► Fig.33: 1. Ring 2. Hook
NOTE: If the tool is bike handle type, attach the band
so that the band passes through inside of the waist
belt as shown in the figure.
► Fig.34: 1. Waist belt 2. Band
2. Attach the hook to the tool.
► Fig.35: 1. Hook
Detaching the tool
Push the levers on the buckle to unlock the buckle.
► Fig.36: 1. Lever
NOTE: The buckle is not equipped depending on the
type of band.
Emergency detachment
1. Push the levers on the buckle of the waist belt to
unlock the buckle.
► Fig.37: 1. Buckle 2. Lever
2.
Take off the shoulder harness to release the tool
and the unit.
► Fig.38: 1. Shoulder harness
15 ENGLISH